User manual ACR ELECTRONICS NAUTICAST REV M

[. . . ] Please read this first! Warning: Although ACR strives for accuracy in all its publications; this material may contain errors or omissions, and is subject to change without prior notice. ACR shall not be made liable for any specific, indirect, incidental or consequential damages as a result of its use. ACR components may only be used in safety of life devices or systems, with the express written approval of ACR, as the failure of such components could cause the failure of the ACR device or system. If these fail, it is reasonable to assume that the safety of the user or other persons may be endangered. 2 Y1-03-0203 Rev. [. . . ] Type 170, actuate "Enter " Type 30, actuate "Enter " Type 15, actuate "Enter " Type 15, actuate "Enter " The AIS calculates Length and Beam: Len (A+B): 200m Beam(C+D): 30m Setting of the internal GPS antenna position: A = 171m the distance from bow to the antenna B= 29m the distance from the antenna to the stern C = 0m the distance from the port side to the antenna D = 30m the distance from the antenna to the starboard side Move with Left/Right and Up/down keys to A:. Type 171, actuate "Enter " Type 29, actuate "Enter " Type 0, actuate "Enter " Type 30, actuate "Enter " The AIS calculates Length and Beam: Len (A+B): 200m Beam(C+D): 30m The calculated Length (A+B) and Beam (C+D) of external and internal GPS antenna position must be the same value, other your entered distances are wrong and the AIS shows in the last line: >>> ext/int ship length doesn't match After correct settings of external and internal GPS antenna reference points the AIS allows to press M5 - [Save]. M N48^12' E 16^26' |1> N/A|2> N/A|3> N/Anm ************ Ship Settings ************* Call Sign:SO52 /\ + ShipName :SOLAS 52 / \| Ref. Points ext int | | A: 170m 171m | A B: 30m 29m | | C: 15m N/A | +--| D: 15m 30m | |B Len (A+B): 200m 200m | || Beam(C+D): 30m 30m +-C-+D-+ Ship Type: N/A or no ship >>> DATA OK. PRESS M5 TO SAVE DATA <<< ---------------------------------------NUM| Save | | | Back | Save Back | | | 3. 5. 5 Transponder Configuration (User Password Protected) The Configuration Menu allows the user to alter the hardware-based parameters. Accessing the Configuration Settings: The Configuration Menu is User Password protected. NOTE: The default password from the factory is mentioned on your AIS display at the protection foil. (see Appendix 0 for password information). N 1o33' E 0o26' |1>01. 10|2>1. 30| * 1A1L |---------------------------------| 5. GPS Settings | -----| | Displ| ---------------------------------------NUM| Select->| | |<-Back Dynamic Keys: Transponder Configuration [M5] [Select] Select desired Submenu [M8] [Back] Return to Main Menu Y1-03-0203 Rev. M 47 Accessing the Configuration Menu with the default User Password N 1o18' E 0o12' |1>0. 10|2>1. 30|3>1. 80nm ---------------------------------------++++++++++++++++++++++++++++++++++++++++ User password protected!Please enter user password: **** ++++++++++++++++++++++++++++++++++++++++ ---------------------------------------| Enter | | | Exit Dynamic Keys: Input of Default User Password to Access Configuration [M5] [Enter] Confirm Default User Password Input [M8] [Exit] Return to Vessel Listing Incorrect User Password Input If the incorrect User Password is input, the screen below appears. N 1o34' E 0o27' |1>0. 10|2>1. 30| * 1A1L ---------------------------------------- ++++++++++++++++++++++++++++++++++++++++ Access denied!++++++++++++++++++++++++++++++++++++++++ ---------------------------------------| | | | <-Exit Dynamic Keys: User Password Input (Access Denied) [M8] [Exit] Return to Vessel Listing 48 Y1-03-0203 Rev. M a) Change User Password (for initial NAUTICASTTM Operation) It is strongly recommended to change the default User Password upon initial NAUTICASTTM operation. Should the new password include numbers, use the shift key to generate them. N 1o19' E 0o12' |1>0. 10|2>1. 30|3>1. 80nm |---------------------------------| 5. | | -----| | Displ| ---------------------------------------NUM|Select->| | |<-Back N 1o33' E 0o27' |1>0. 10|2>1. 30| * 1A1L ********* Change User Password ********* Enter new password: Repeat new password: ***** ***** {Length: 6. . 8 characters} ---------------------------------------| Enter | | | Back Dynamic Keys: Initial User Password Setting [M5] [Enter] Confirm User Password Input [M8] [Back] Return to Menu Configuration Y1-03-0203 Rev. M 49 This screen appears if the new User Passwords are mismatched - i. e. the New User Password and the Repeated New User Password are not identical. In this case, it is possible to re-input both the New and Repeated User Passwords again. [Exit] takes the user back to the User Password Input Screen. N 1o19' E 0o13' |1>0. 10|2>1. 30|3>1. 80nm ---------------------------------------- ++++++++++++++++++++++++++++++++++++++++ Passwords mismatched!++++++++++++++++++++++++++++++++++++++++ ---------------------------------------| | | |<-Exit Dynamic Keys: User Password Input (Password Mismatched) [M8] [Exit] Return to Password Input Screen The new User Password configuration has been saved. N 1o33' E 0o27' |1>0. 10|2>1. 30| * 1A1L ---------------------------------------- ++++++++++++++++++++++++++++++++++++++++ Data saved. ++++++++++++++++++++++++++++++++++++++++ ---------------------------------------| | | | <-Exit 50 Y1-03-0203 Rev. M b) Region Settings A Region is a defined area, with specific VHF parameters, which are sent out by Vessel Traffic Service Stations (VTS), and received via Digital Selective Calling (DSC) or AIS. When the vessel enters into one of the pre-defined Regions, the NAUTICASTTM automatically switches to the relevant Region Setting. [. . . ] 78, 20359 Hamburg, Germany Inland AIS Type Approval Certificate No: R - 4 - 203 Issued by: Fachstelle der WSV für Verkehrstechniken Weinbergstraße 11-13, 56070 Koblenz, Germany IMO MSC. 74(69) Annex 3 ITU-R M. 1371-3 (Class A) IALA Technical Clarifications of Rec. 1. 3) ITU-R M. 825-3 ITU-R M1084-3 IEC 61993-2 (2001) IEC 61162-1 (2000), -2 (1998) IEC 60945 (1996) IEC 61108-1 (1996) Technical Specification for Vessel Tracking and Tracing Systems for Inland Waterways (Ed. 1. 01 dated 10. 10. 2007) Test Standard for Inland AIS, (Edition 1. 0 dated 31. 5. 2007) 2009-08 ACR Electronics Inc. , 5757 Ravenswood Road, Fort Lauderdale, Florida, 33312 USA ACR Electronics Europe GmbH Handelskai 388 / Top 632 A-1020 Vienna, Austria Vienna, 2009-07-22 Zertifikate der benannten Stelle: Certificates from the notified Body / Certificats des Organismes Notifiés Spezifizierte Standards: Specified Standard(s) / Standard(s) Spécifié(s) Dokumentennummer: Document number / Num. du document Hersteller: Manufacturer / Fabricant Anschrift EU-Vertretung: Address EU-Representative / Adresse du Représentant pour l'UE Ort, Datum: place, date / Lieu, Date Unterschrift: Signature / Signature Andreas Lesch Managing Director Diese Erklärung bescheinigt die Übereinstimmung mit den genannten Richtlinien, ist jedoch keine Zusicherung von Eigenschaften. [. . . ]