User manual ACR ELECTRONICS RCL-75

[. . . ] bolts 4 each, Lock nuts 4 each, Washers 1 each, 1/4" Drill bit for bolt holes 1 each, 15/16" Drill bit for cable clearance 1 each, 13/64" Drill bit for remote switch mounting bolts 1 each, Tube of silicone or bedding compound to close hole around cable OR 1 each, 17/64" Drill bit for lag screws OR 4 each, 1/4" dia. Lag screws OPTION: 1-inch mounting riser shapeable for irregular surfaces (P/N 9427, see Figure 6). Location Selection Care and consideration should be given to the selection of a mounting location for the RCL-75 and the Point PadTM (remote control panel). Typical mounting locations include bow pulpit, fore deck, and cabin hardtop (see Figures 2 and 3). [. . . ] Use the gasket, washers, nuts, and the two U-Clamps provided to secure the Point PadTM. Make sure there are no obstructions behind the area where the switch is to be located. bulkheads, wires, plumbing, hardware. ) Check in advance to verify the wiring harness can be routed to this location. Figure 4Point PadTM surface mount Figure 5Point PadTM flush mount Mounting the Light Make sure area is clean and dry. Verify that the backside of the mounting surface can be reached to install nuts and washers. NOTE: If the mounting surface is not flat, a special, shapeable plate can be purchased, (P/N 9427), to adapt the light base to the surface. This plate can also be used to raise the light 1 inch (2. 54 cm) if desired (see Figure 6). Y1-03-0158G 8 Figure 6-Shapeable plate (purchased separately) Remove the deck mounting plate from the light base (4 Allen bolts). Rotate the plate so that the arrows are pointing forward and the length of the arrow is aligned parallel to the keel. Mark the 4 mounting holes, starting with the hole marked "Front" on the mounting plate. Drill 4 mounting holes (1/4") and a centered cable clearance hole (3/4"). Use caulk or bedding compound to seal bolt and wire holes before deck mount is attached to deck. The plates are keyed to each other and to the light: Be sure the arrows are pointing in the correct direction. Use marine grade 316 stainless steel bolts, nuts, and lock washers to fasten the plate(s) to the mounting surface. Install and connect the control cable and (+) Red and (-) Black power leads. Leave at least 8 inches (20. 32 cm) of wire coiled in the base of light to allow for servicing (see Figure 7). Figure 7 Y1-03-0158G 9 Seat the light assembly on the deck mount. Reinstall the four (4 ) stainless steel Allen bolts with the flat washer next to the plastic and the lock washer under the bolt head. Tighten securely. SECTION 4 - OPERATION The remote control Point PadTM is simple to operate. The control disk is pushed down in the direction you want to aim the light. Elevation and rotation can be operated at the same time, with the light in the ON or OFF mode. SECTION 5 - CARE AND MAINTENANCE General maintenance The RCL-75 is relatively maintenance free. Clean the exterior of the light with a mild detergent and water if desired. Rotate the light left, then right and up then down periodically to keep motors and turning surfaces clean and operational. If they should need replacement, they can be ordered through an ACR dealer or ACR Electronics. CAUTION: Failure to follow replacement instructions carefully can result in damage to bulb and/or light. [. . . ] To ensure that you have the most recent version of the Product Support Manual, please visit the ACR website at www. acrelectronics. com. Reproduction in whole or in part is permitted only with permission of ACR Electronics, Inc. Ongoing product improvements may change product specifications without notice. Trademarks or registered trademarks are the property of their respective owners. Y1-03-0158G 18 EC DECLARATION OF CONFORMITY ACR Electronics, Inc. [. . . ]