User manual ADVANCE ACOUSTIC MAP-102 QUICK START

[. . . ] WATER AND MOISTURE The appliance should not be used near water for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. VENTILATION The appliance should be situated so that its location or position does not interfere with its proper ventilation. Sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. HEAT The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliance (including amplifiers) that produce heat. [. . . ] Afficheur H AUXILIARIES INPUTS AUX1 AND AUX2 Press this button to select the Auxiliary 1 or auxiliary 2 as your listen source. Also on this input, you have the possibility to use others sources with same audio signal output like tuner, tape, MD, etc. Afficheur H AUXILIARIES INPUTS AUX3 AND AUX4 Press this button to select the Auxiliary 3 or auxiliary 4 as your listen source. Also on this input, you have the possibility to use others sources with same audio signal output like tuner, tape, MD, etc. Afficheur H PHONO INPUT Press this button to select the phono input as your listen source. Afficheur H USB INPUT The USB (MP3 only) port allows you to hook up your MP3 Player or MP3 drive to play back your downloaded MP3 music library directly thru the MAP-102 amplifier. HEADPHONE You can connect a stereo headphones to the phone jack for private listening. Please note that all connected speakers are turned off automatically while the headphones plug is inserted in the phone jack. Press the speakers button to toggle through the four speaker selections: Off, pair A, pair B and pairs A+B. Adjust the level of B, M (Attention, you can listen the medium adjustment after one second) and T with the volume/control button from -10 to +10 (indicator C) When the adjustment is done, wait 5 secondes and your adjustments will be memorised automatically. the MAP-102 integrates a direct mode signal that could be activate by pushing the Tone button (the display will show Off). When the direct Tone is on, the tone controls are bypassed, so you can enjoy a pure sound. Mode Off (indicateur D ) et mode 1, 2, 3 ou 4 (indicateur E ) AUDIO OPTIMIZER FOR PC1 AND iPod Press the PC/iPod Equalizer button to toggle through the five selections: Off, 1, 2, 3 and 4. In Off mode, the audio signal coming from your PC1 or iPod is not going thru the optimizer processor. In mode 1, 2, 3 and 4, the audio signal coming from your PC or iPod is optimised to obtain a more "audiophile" sound. LEVEL PC1/iPod Press this button to boost the audio signal coming from your PC1 or iPod. Class'A) HIGH BIAS LIGHT INDICATOR This light indicator is ON when High Bias function is active. PC1 MINIJACK INPUT Connect your PC with a minijack cable (3, 5mm) IPod MINIJACK INPUT You can connect your iPhone or iPod with a minijack (3, 5mm) male cable. It would take about one second to discharge the CPU (central processing unit, in fact the processor that carries out the instructions). If the user switch off and switch on the unit for many times within one second, it shall cause potential damage to the unit Connect the right speaker to the terminals market `R +' and `R-' ensuring that the `R+' is connected to the `+' terminal on your loudspeaker and the `R-' is connected to the loudspeaker's `-' terminal. connect the terminals marked `L+' and `L-' to the left speaker in the same way. When using both SPEAKERS A and SPEAKERS B connect speakers of impedance 8 Ohms or greater. [. . . ] PRE OUT 2 / CONNECTING ANOTHER POWER AMPLIFIER OR SUBWOOFER These jacks allow you to connect another power amplifier or an active subwoofer (subwoofer with built-in amplifier). To connect them use an analog audio cable to connect the amplifier's L/R PRE OUT 2 jacks to the analog audio input jacks of your powered subwoofer or power stereo amplifier. IN / POWER AMPLIFIER IN If you only want to use the power amplifier section of your MAP-102, you can connect another preamplifier or audio mixer on L/R AMP. HIGH BIAS SELECTOR By switching the High Bias mode in ON mode, your amplifier will be similar as a Class'A amplifier of the first watts of use. [. . . ]