User manual ADVANCE ACOUSTIC MPP-506 QUICK START GUIDE

[. . . ] WATER AND MOISTURE The appliance should not be used near water for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. VENTILATION The appliance should be situated so that its location or position does not interfere with its proper ventilation. Sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. HEAT The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliance (including amplifiers) that produce heat. [. . . ] When set to STANDBY the main power is cut-off and the unit is no longer fully operational except for the micro controller. CD INPUT UNBALANCED, CD INPUT BALANCED AND TUNER Press this button to select the CD RCA unbalanced (blue bottom led), press again to select CD Bal. Balanced (red bottom led) and another time to select Tuner (blue top led). AUXILIARY 1 AND AUXILIARY 2 INPUTS Press this button to select AUX1 (blue bottom led), press again to select AUX2 (blue top led). eNTRÉES COAXIAL 1 , COAXIAL 2 , OPTICAL ET USB (MPP-506DA) Appuyez sur ce bouton pour sélectionner l'entrée COAX1 (led bleu inférieure) , appuyez à nouveau pour choisir l'entrée COAX2 (led rouge inférieure) , une nouvelle fois pour sélectionner l'entrée OPT (led bleu supérieure) enfin une pression supplémentaire sélectionnera l'entrée USB (led rouge supérieure). COAXIAL 1, COAXIAL 2, OPTICAL AND USB INPUTS (MPP-506DA) Press this button to select COAX1 (blue bottom led), press again to select COAX2 (red bottom led), another time to select OPT (blue top led) and last time to select USB input (red top led) PHONO AND AES/EBU (MPP-506DA) INPUTS Press this button to select PHONO (blue bottom led), press again to select AES/EBU (blue top led). The back panel, you have the possibility to adjust the cartridge type used: MM for moving magnet cartridges and MC for moving coil cartridges. Gh PC RCA, PC JACK AND lp INPUTS Press this button to select the PC RCA (red bottom led), press again to select PC JACK (blue bottom led) and another time to select ip (blue top led). Please note that two inputs connectors for PC JACK and ip are on the front panel, their input levels has been optimised (stereo minijack 3, 5mm). HEADPHONES The headphone terminal provides a stereo audio signal sufficient for driving all conventional stereo headphones except electrostatic headphones which generally require signal from a high level ouputs. VOLUME BUTTON Your amplifier used a rotary type knob to control the 2 channel output sound level (left and right). Turn this volume knob clockwise to increase the ouput sound level and turn this volume knob counterclockwise to decrease the output sound level. ISOLATING SPIKES Your amplifier used spike-feet, you need to use them with non-skid cupels included. The led DAC INSIDE lights up when your preamplifier is a MPP-506DA or a MPP-506 with DAC board inside. To obtain additionnal informations about this upgrade card, please contact your appointed dealer. Don't place the unit sideways, a big power exerts on the single side of the plate. These inputs are suitable for any line level source equipment such as tuners, CD players, DVD, MP3 players, etc. They should not be connected to the digital output of a CD player or any other digital device. PHONO INPUT, MM/MC SWITCH AND GROUND TERMINAL You can connect your turntable and adjust the cartridge type (MM or MC cartridge). PRE-OUT / SUBWOOFER OUT / HIGH PASS OUT / CROSSOVER FREQUENCY PRE-OUT: These connections allow you to connect L and R input from your power amplifier here. [. . . ] L de votre préamplificateur MPP-505 BALANCED CD INPUT If your cd player has a stereo balanced output, you can connect it on the stereo balanced cd input of your preamplifier MPP-505. Also, you can use this balanced input with others sources like tuner, DVD, etc. AES/EBU INPUT (ONLY MPP-506DA) The digital audio standard frequently called AES/EBU, officially known as AES3, is used for carrying digital audio signals between various devices. it was developed by the Audio Engineering Society (AES) and the European Broadcasting Union (EBU) and first published in 1989 (Watkinson , 1989) , later revised in 1995 , 1998 , and 2003. [. . . ]