User manual ALTO ATTIX 360-2H SPARE PARTS

[. . . ] 2 THERMAL SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CHAPTER 1 INTRODUCTION OF 830CN/830CH/ATTIX 360-2H MOTHERBOARD 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PERFORMANCE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power switch: PW BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. Turbo LE D R eset SW Speaker G ND NC (5) (6) (7) (8) IDE D LE PW BTN SMI SW G ND VC C NC G ND VC C G ND G ND System Case Connections (9) Wake On-LAN Headers (3-pin): WOL 20 Power LE D Turbo SW VC C This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled. WOL 1 3 5VSB G ND WO N Wake-On-LAN Headers (10) FAN Speed Headers (3-pin): CPUFAN, SYSFAN These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. Connect the fan's plug to the board taking into consideration the polarity of connector. CPUFAN 1 3 SYSFAN 1 3 (11) IR infrared module Headers (9-pin): IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. IR VC C IR X R G ND IR TX 5 10 1 6 C IR NC CR IR X IO VSB NC NC IR: (Pin1Pin5) for Standard IR CIR: (Pin6Pin10) for Consumer IR Infrared Module Headers (12) CD Audio-In Headers (4-pin): CD_IN, CD_IN2 CD_IN and CD_IN2 are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. 21 1 4 C D_IN2 1 4 C D_IN CD Audio-In Headers (13) AUX-In Headers (4-pin): AUX_IN AUX_IN 4 1 AUX In Headers (14) Audio External Connector (9-pin): AUDIO AUDIO Pin 1 L-IN-L G ND MIC L-O UT-L L-IN-R G ND MIC P G ND L-O UT-R Audio External Connector 22 2-7 Starting Up Your Computer 1. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. The LED on the monitor may light up or switch between orange and green after the system is on. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. CMOS Setup Utility ­ Copyright(C) 1984-2000 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Esc : Quit F10 : Save & Exit Setup Miscellaneous Control Load optimized Defaults Load Standard Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item Time, Date, Hard Disk Type. . . Figure 3-1 Standard CMOS Features Use this Menu for basic system configurations. Advanced BIOS Features Use this menu to set the Advanced Features available on your system. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system's performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. 25 Power Management Setup Use this menu to specify your settings for power management. PnP/PCI configurations This entry appears if your system supports PnP/PCI. Miscellaneous Control Use this menu to specify your settings for Miscellaneous control. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values for the minimal/stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Exit Without Saving Abandon all CMOS value changes and exit setup. 3-4 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categories. [. . . ] This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL supports WINDOWS 95/98/98SE/ME/NT4. 0/2000 Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or click START / click RUN / type X:\SETUP. EXE (assuming X is your CD-ROM drive). From MAGIC INSTALL MENU you may make 11 selections: 1. [. . . ]