User manual ANSMANN XMOVE DELUXE

[. . . ] Shows the battery type and the different functions NiCd = NiCd battery NiMH = NiMH battery LiIo = LiIon battery LiPo = LiPo battery PB = Lead Acid battery CHG = Charge DIS = Discharge CD = Cycle Mode, first charge then discharge (NiCd and NiMH batteries) CD = Cycle Mode, first discharge then charge (NiCd and NiMH batteries) 2. Shows the battery type (Chemistry) during charge/ Capacity / charge or discharge current NC = NiCd battery NH = NiMH battery LI = LiIon battery LP = LiPo battery PB = Lead Acid battery CAP = capacity (at NiCd or NiMH) C = capacity (at LiIon, LiPo or Lead Acid) C = charge current D = discharge current 3. Due to its DC input on the primary side this charge can be used connected to a car battery or another 11-15V DC high current supply and is independent from a mains power supply system. The Micro controller inside the xMove Deluxe charger will ensure that all set modes; charge / discharge / cycle are controlled in a very precise way. [. . . ] Now use the "INC" or "DEC" button to get to "CHARGE" and then push "ENTER" to confirm. after your confirmation the display will change to the capacity "CAP". Now please set the capacity of your battery with the buttons "INC" or "DEC" from 100 mAh to 5000 mAh and confirm with "ENTER". The display changes to the charge current "C" which can be set with the "INC" or "DEC" buttons from 0. The parameters shown on the display are set and stop flashing if no push button is pressed for 3 seconds. After a short check of all parameters the display shows the battery type "NC", the charge mode "CHG", the charge current e. The clock starts running in seconds and the display shows also the charged capacity. The display shows the trickle charge current and the capacity charged into the battery. Push the button "BATT TYPE" until the display shows "NiCd". Now use the "INC" or "DEC" button to get to "DISCHARGE" and then push "ENTER" to confirm. after your confirmation the display will change to the discharge current "D". Now please set the discharge current with the buttons "INC" or "DEC" from 0. The display changes to the discharge voltage "V" which can be set with the "INC" or "DEC" buttons from 0. The parameters shown on the display, are set and stop flashing if no push button is pressed for 3 seconds. After a short check of all parameters the display shows the battery type "NC", the discharge mode "DIS", the discharge current e. The clock starts running in seconds and the display shows also the discharged capacity. Within the CYCLE MODE you can choose between 2 options; a) "CD" to identify the battery capacity. Push the button "BATT TYPE" until the display shows "NiCd". Now use the "INC" or "DEC" button to get to "CYCLE" and than push "ENTER" to confirm. Now please set the cycle mode with the buttons "INC" or "DEC" from "CD" or "C D" and confirm with "ENTER". The display changes now to the number of cycles which can be set with the "INC" or "DEC" buttons from 1 to 5. after your confirmation the display will change to the capacity "CAP". [. . . ] LiIon = 3, 6 V / cell LiPo = 3, 7 V / cell LiIon = 2, 6 V / cell LiPo = 2, 8 V / cell Adjustments and the associated display you can be seen in the following chart: Push the button "BATT TYPE" until the display shows "PB". Now use the "INC" or "DEC" button to get to "CHARGE" and then push "ENTER" to confirm. After your confirmation the display will change to the charge current "C" which can be set with the "INC" or "DEC" buttons from 0. Of cells / cell voltage which can be set with the "INC" or "DEC" buttons from 1 cell = 2V pack; 2 cells = 4V pack; 3 cells = 6V pack; 4 cells = 8V pack, 5 cells = 10. [. . . ]