User manual ASUS VW22ANL

[. . . ] / Push the 'SOURCE', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal. ) If you select the digital mode, you must connect your monitor to the Use this button for auto adjustment. >> Click here to see an animation clip Use this button for turning the monitor on and off. This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. AUTO button Power button [ ] Power indicator See PowerSaver described in the manual for further information regarding power saving functions. [. . . ] For using a locking device, contact where you purchase it. See Connecting Cables for further information regarding cable connections. Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. - Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card. -Connect the monitor to the Macintosh computer using the D-sub connection cable. If the monitor and the computer are connected, you can turn them on and use them. Using the Stand Monitor Assembly Monitor and Bottom Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad. A. Mounting interface pad (Sold separately) Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Is the power cord connected properly?Can you see "Check Signal Cable" on the screen? Solutions Check the power cord connection and supply. (Connected using the D-sub cable) Check the signal cable connection. (Connected using the DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. The screen colors have changed after changing the video card. Have the Windows colors been set properly? monitor, Plug & Play (VESA DDC) monitor found". See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Install the monitor driver according to the Driver Installation Instructions. Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. (If it does, request an a service for the main board of the computer. ) If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution. ) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel ¡æ System ¡æ Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center. Q&A Question How can I change the frequency?Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details. ) How can I adjust the resolution?Windows XP : Set the resolution in the Control Panel ¡æ Appearance and Themes ¡æ Display ¡æ Settings. Windows ME/2000 : Set the resolution in the Control Panel ¡æ Settings. Display ¡æ Contact the video card manufacturer for details. Windows XP : Set the resolution in the Control Panel ¡æ Appearance and Themes ¡æ Display ¡æ Screen Saver. [. . . ] Do not let any water enter the monitor. Self-Test Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check Turn off both your computer and the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. [. . . ]