User manual AXIS 207

[. . . ] AXIS 207/207W Network Camera User's Manual About this Document This manual is intended for administrators and users of the AXIS 207/207W Network Camera, and is applicable for software release 4. 30 and later. It includes instructions for using and managing the AXIS 207/207W on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be beneficial, for developing shell scripts and applications. [. . . ] Keep the Control button pressed until the Status Indicator color changes to amber (this may take up to 15 seconds). When the Status Indicator changes to Green (which may take up to 1 minute), the process is complete and the camera has been reset. The unit will now have the default IP address 192. 168. 0. 90 Advanced Scripting is an advanced function that provides the possibility to customize and use scripts. Improper use may cause unexpected behavior or even cause loss of contact with the unit. If a script does cause problems, reset the unit to its factory default settings. A backup file may be of use to return the unit to its latest configuration. Axis strongly recommends that you do not use this function unless you fully understand the consequences. Note that Axis support does not provide assistance for problems with customized scripts. For more information, please visit the Developer pages at www. axis. com/developer Plain Config - this function is for the advanced user with experience of Axis network camera configuration. Help is available from the standard help pages. AXIS 207/207W - The I/O Terminal Connector 37 The I/O Terminal Connector Pinout and Interface The 4-pin I/O terminal connector provides the interface to: · 1 transistor output · 1 digital input · auxiliary power and GND The terminal connector is used in applications for e. g. motion detection, event triggering, time lapse recording, alarm notification via email, etc. If the pushbutton is pressed, the state changes and the input becomes active (shown under Event Configuration > Port Status). an alarm device that can be activated by Output buttons on the Live View page, or by an Event Type. The output will show as active (Event Configuration > Port Status) if the alarm device is activated. Function Transistor Output Pin 4 Description With a maximum load of 100mA and a maximum voltage of 24V DC, this output has an open-collector NPN transistor with the emitter connected to the GND pin. If used with an external relay, a diode must be connected in parallel with the load, for protection against voltage transients. Connect to GND to activate, or leave floating (or unconnected) to deactivate. Pinouts The I/O terminal pins on the AXIS 207 and AXIS 207W are numbered as shown below. AXIS 207 4 1 Digital Input GND Auxiliary DC Power Input 3 1 (AXIS 207W) 2 (AXIS 207) 1 (AXIS 207) 2 (AXIS 207W) AXIS 207W 1 4 5VDC/min 2. 5W (AXIS 207) 5VDC/min 3. 5W (AXIS 207W) Electrically connected in parallel with the connector for the PS-L/PS-H power adapter, this pin provides an auxiliary connector for mains power to the unit. This pin can also be used to power auxiliary equipment, max 50mA. 38 AXIS 207/207W - The I/O Terminal Connector Connect input/output devices to the camera as follows: 1. Attach the cables for the device securely to the supplied green connector block. Once the cables are connected, push the connector block into the terminal connector (also green) on the camera. Terminal Connectors AXIS 207 3. 3V Linear Power Supply Fuse 500mA + o PS-L 2. 5W o 1 o e. g. [. . . ] The advantage of UDP is that it is not required to deliver all data and may drop network packets when there is e. g. This is suitable for live video, as there is no point in re-transmitting old information that will not be displayed anyway. Unicast - Communication between a single sender and a single receiver over a network. URL (Uniform Resource Locator) - An "address" on the network. [. . . ]