User manual B&K CT610

[. . . ] B & K Components, Ltd. User Manual CT610 CT310 CT602 CT600 CT300 Multi-Zone Audio/Video Receivers 13226 0905 COMPLETE USER MANUAL - CT RECEIVER © 2005 B & K Components, Ltd. All rights reserved. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from B & K Components, Ltd. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. [. . . ] The alternative to mono split zones is to assign the the master bed and master bath to separate independent zones. See next section for Code-Set description. S IMPLY B ETTER! B&K Code-Set Description and Overview 41 Code-Set Description and Overview B & K uses discrete code-sets to control any or all of its audio/video zones. This is the same practice that satellite manufacturers use so that one remote controller could control three identical satellites. The satellites are first set (via switches or on-screen menus) to be either an A, B or C satellite. When the remote control is set to SAT A, only SAT A responds and so on. In the advanced setup menu of the CT Receiver Code-Sets are assigned to control each zone. Once the codes have been assigned, functions like lowering the volume in Junior's room from the Kitchen keypad is possible. Code-Sets can also control a group of zones (such as upstairs or party modes) or control the whole house (all zones) using Code-Set 0-0-0. In a basic default system, all keypads are pre-programmed with Code-Set 1-2-8. The CT Receiver monitors which one of the six Zone Control terminals the IR command was received from and responds only in that zone. Thus, as long as each keypad is hard wired to the correct Zone Control terminal, all keypads can be programmed identically using code 1-2-8. However, the user can be provided with powerful convenience features by utilizing discrete Code-Sets to enable any keypad to control any zone, any group of zones or the whole house. The front panel will not respond to Code Set 1-2-8 received from a remote control. B & K created 128 different sets of the same CT Receiver commands. These commands will also work with B & K home theater units assigned to the same code set. The primary commands are as follows: Power State ZONE POWER ON POWER OFF Tone BASS BASS + TREBLE TREBLE + LOUDNESS Input Sources SOURCE + SOURCE VIDEO SOURCE + DEDICATED IN INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 INPUT 7 INPUT 8 INPUT 9 TUNER Tuner AM FM BAND TOGGLE TUNE TUNE + STATION STATION + Volume MUTE ON MUTE OFF STEREO/MONO MUTE (TOGGLE) MASTER VOL+ MASTER VOL- *This list is not a complete list of commands. For a complete list please refer to page 7 of this manual. Each code-set differs from the next only in the initial IR code identification or prefix, i. e. This way a CT Receiver zone can be setup to recognize an intended command no matter what Zone Control terminal the command is received from. Thus, any zone can control any other zone (or group of zones) by programming a remote control or a keypad with the appropriate set or sets of codes from the following choices: Code Code Code Code Set Set Set Set 000 Controls ALL zones simultaneously. (Multi Zone and Home Theater) 001-127 Can be utilized for group or independent zone operation. (Discrete) 128 Controls only the zone it is connected to or received from. (Hardware Specific) 999 Controls a set of B & K ALL commands (Multi Zone and Home Theater) S IMPLY B ETTER! B&K 42 Groups / Code Sets / Zones - Tab 2 You can program a maximum of 18 groups for each CT Receiver labeled a - r for your reference only. [. . . ] In case you encounter any "Out of Memory" or "Out of Resources" errors, be sure your PC meets the minimum requirements outlined in the BKcSuite section of this manual. It is recommended to let Windows manage your virtual memory, however, if you manually set the virtual memory size, set it at least 1. 5 times your actual RAM size. Troubleshooting Guide for CT Receivers Problem CT receiver will not power up Keypads will not power up Keypad won't pass IR On Screen Menu won't display Keypads are going to blank page Slaved Keypads are not operating properly Control of Sources is inconsistent or not operating at all Possible Solution Check power cord and/or power supply. See page 52. Limited Warranty B & K Components Ltd. , referred to herein as B & K , warrants your B & K equipment against all defects in material and workmanship for a period of five years from the date of purchase. This warranty applies only to the original purchaser and only to equipment in normal residential use and service. [. . . ]