User manual BARRACUDA C400 INSTALLATION REV 1.3

[. . . ] Read and follow all instructions before attempting to unpack, install or operate this equipment, especially before connecting the power adapter. Electrical Safety Basic electrical safety precautions should be followed to protect yourself from harm and the appliance from damage: · Be aware of the power switch locations on the appliance's chassis as well as the emergency power-off switch for the housing room, the disconnection switch or the electrical outlet. Knowing these locations enables you to quickly remove electrical power from the system in case an electrical accident occurs. When working around exposed electrical circuits, another person who is familiar with the power-off controls should be nearby to switch off the power if necessary. This is to avoid making a complete circuit, which will cause electrical shock. [. . . ] Put the server board and peripherals back into their antistatic bags when not in use. For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the server board. After accessing the inside of the system, close back the system and secure it to the rack unit with the retention screws after ensuring that all connections have been made. · 7 Safety Instructions Introduction and Package Contents Your new Barracuda NG Control Center C400 is a management appliance preinstalled with firmware to centrally manage Barracuda NG Firewall appliances in a secure, reliable and efficient way. Hardware Configuration Table 1 Hardware Component CPU Memory HDD Flash Disk Form Factor Dimensions (W/D/H) Net Weight Power Supply Input Voltage Power Supply Frequency Storage Temperature Operation Temperature Relative Humidity Certifications Description AMD Athlon dual core 2 GB 2 x 3. 5" 250 GB, 7200 rpm 4 GB 1U Full Size 42. 7 x 4. 3 x 57. 4 cm 11. 8 kg 100 - 240 V, AC 47 Hz - 63 Hz -20 °C - +70 °C 0 °C - 40 °C 5% - 95%, non-condensing CE, FCC, ROHS The hardware configuration list in Table 1 was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological progress. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NG Firewall or NG Control Center appliance it was delivered with. Inspecting the Package The following items are included in the package: · · · · One security appliance One power cord Printed Quick Start Guide One USB flash drive including documentation and administrative tools Please contact Barracuda Networks support if any of these items is missing. 8 Appliance Installation Guide Powering Up and Down This chapter describes the procedure used to install your appliance and perform the initial configuration. Powering Up the Appliance · · · · Connect and power on the appliance. The current status of the boot process will be shown on the appliance's LCD display. After a few seconds, the boot process will be initiated and the status LED should start to blink green. Wait until the status LED indicates constant green: The booting procedure is finished. Powering Down the Appliance You must never turn off the appliance by simply switching it off or otherwise removing power from it. Always initiate a proper system shutdown as described below. · · · The system shutdown must be initiated either using the Barracuda NG Admin tool, a remote logon to the appliance or by using the LCD display and keypad on the appliance. The current status of the shutdown process will be shown on the appliance's LCD display. The status LED will turn off at the end of the shutdown procedure. 9 Powering Up and Down The Status LED Your appliance is equipped with a variety of LEDs. It indicates the appliance's operational state by changing colors between green, orange and red and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states. Table 2 Status LED Conditions Color Off Glowing State Off Meaning Installation Appliance is powered off or installation has not initialized far enough for LED control when installation is started. Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control. Meaning Normal Operation or ART Appliance is powered off. Appliance is either booting, shutting down or performing a system update. An error has appeared preventing Barracuda NG Firewall from entering the up state. Green Blinking Green Steady Red Blinking Error during installation. If no orange light available: appliance is in ART mode. Appliance is in ART mode. Red Orange Orange Steady Blinking Steady - Not all appliances support orange and/or red LED colors. Depending on the appliance type, the status LED might be on by default and it might take some time during boot and installation to start either blinking or changing the color. For flash-only appliances, this option always requires an USB thumb drive connected to the system. The system will be recovered either to the release version of Barracuda NG Firewall it was first installed in, losing the updates installed since then, or to the state stored in a PAR file residing within the art partition of the system drive. Once your appliance is readily configured, you may save the configuration for ART recovery through Box > Active Recovery > Save Current Config. This will generate an ISO file within the art partition that will be used during the next recovery process. ART system recovery only works if the appliance was installed with Barracuda NG Firewall 5. 0. It is not possible to use ART system recovery on systems that were updated from 4. 0 or 4. 2. See Using ART Recovery without USB Stick, page 13, in order to learn about the ART recovery process. [. . . ] If the appliance was recovered using an USB stick generated with the Barracuda NG Install application specifically for this appliance type, the second reboot is not necessary and the appliance will boot directly into operation mode. · · · · Using ART Recovery without USB Stick · If you want to recover using your current configuration, first save your configuration for ART through Barracuda NG Admin using Box > Active Recovery > Save Current Config or put a PAR file named box. par into the art partition's root directory. Boot into the ART menu as described above in (the Status LED blinks orange when ART is running) and choose Start recovery. Recovery is finished as soon as the Status LED steadily indicates green. · · 13 Installation and Recovery Using ART Errors During Recovery If difficulties are encountered during the recovery process, the Status LED will blink red. Furthermore, you may also trace the output using the serial console. 14 Appliance Installation Guide Connecting to the Network and Configuring Fig. [. . . ]