User manual BARRACUDA F200 INSTALLATION REV 1.3

[. . . ] Read and follow all instructions before attempting to unpack, install or operate this equipment, especially before connecting the power adapter. Electrical Safety Basic electrical safety precautions should be followed to protect yourself from harm and the appliance from damage: · Be aware of the power switch locations on the appliance's chassis as well as the emergency power-off switch for the housing room, the disconnection switch or the electrical outlet. Knowing these locations enables you to quickly remove electrical power from the system in case an electrical accident occurs. When working around exposed electrical circuits, another person who is familiar with the power-off controls should be nearby to switch off the power if necessary. This is to avoid making a complete circuit, which will cause electrical shock. [. . . ] After accessing the inside of the system, close back the system and secure it to the rack unit with the retention screws after ensuring that all connections have been made. · 7 Safety Instructions Introduction and Package Contents Your new Barracuda NG Firewall F200 / F201 is an integrated security appliance preinstalled with Barracuda NG Firewall firmware. This winning combination offers a ready to run security solution that is flexible, affordable and easy to deploy. Hardware Configuration Table 1 Hardware Component CPU Memory HDD (formatted) Flash Disk Form Factor Dimensions (W/D/H) Net Weight Power Supply Input Voltage Power Supply Output Voltage Power Supply Frequency Power Supply Watts Storage Temperature Operation Temperature Relative Humidity Certifications WiFi (F201 only) Description VIA 1. 5 GHz 1 GB 1 x 2. 5", 160 GB 128 MB Desktop 5 x 36 x 19 cm 3, 6 kg 100 - 240 V, AC 12 V, DC 47 Hz - 63 Hz 60 W -20 °C - +70 °C 0 °C - 40 °C 5% - 95%, non-condensing CE, FCC, ROHS 802. 11 b+g or better extended range WiFi adapter The hardware configuration list in Table 1 was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological progress. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NG Firewall or NG Control Center appliance it was delivered with. 8 Appliance Installation Guide Inspecting the Package The following items are included in the package: · · · · · · · · · One security appliance One power cord One external power supply One ethernet crossover cable (red) One ethernet standard cable (grey) One serial cable (console) Printed Quick Start Guide One USB flash drive including documentation and administrative tools One antenna to be mounted to the WiFi adapter (F201 only) Please contact Barracuda Networks support if any of these items is missing. 9 Introduction and Package Contents Powering Up and Down This chapter describes the procedure used to install your appliance and perform the initial configuration. Powering Up the Appliance · · · · Connect and power on the appliance. The current status of the boot process will be shown on the appliance's LCD display. After a few seconds, the boot process will be initiated and the status LED should start to blink green. Wait until the status LED indicates constant green: The booting procedure is finished. Powering Down the Appliance You must never turn off the appliance by simply switching it off or otherwise removing power from it. Always initiate a proper system shutdown as described below. · · · The system shutdown must be initiated either using the Barracuda NG Admin tool, a remote logon to the appliance or by using the LCD display and keypad on the appliance. The current status of the shutdown process will be shown on the appliance's LCD display. The status LED will turn off at the end of the shutdown procedure. 10 Appliance Installation Guide The Status LED Your appliance is equipped with a variety of LEDs. It indicates the appliance's operational state by changing colors between green, orange and red and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states. Table 2 Status LED Conditions Color Off Glowing State Off Meaning Installation Appliance is powered off or installation has not initialized far enough for LED control when installation is started. Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control. Meaning Normal Operation or ART Appliance is powered off. Appliance is either booting, shutting down or performing a system update. · System recovery Effectively invokes a reinstall of the appliance. For hard disk based appliances, an installation "*. iso" image as well as a backup PAR file are stored within a dedicated partition on the hard drive and will be used. Optionally, an *. iso image on an USB thumb drive connected to the appliance may be used. If no PAR file is available, the default installation for the corresponding appliance type is chosen. For flash-only appliances, this option always requires an USB thumb drive connected to the system. The system will be recovered either to the release version of Barracuda NG Firewall it was first installed in, losing the updates installed since then, or to the state stored in a PAR file residing within the art partition of the system drive. Once your appliance is readily configured, you may save the configuration for ART recovery through Box > Active Recovery > Save Current Config. This will generate an ISO file within the art partition that will be used during the next recovery process. ART system recovery only works if the appliance was installed with Barracuda NG Firewall 5. 0. It is not possible to use ART system recovery on systems that were updated from 4. 0 or 4. 2. See Using ART Recovery without USB Stick, page 14, in order to learn about the ART recovery process. [. . . ] Recovery is finished as soon as the Status LED steadily indicates green. · · 14 Appliance Installation Guide Errors During Recovery If difficulties are encountered during the recovery process, the Status LED will blink red. Furthermore, you may also trace the output using the serial console. 15 Installation and Recovery Using ART Connecting to the Network and Configuring Fig. The illustration below shows the connectors located on the back side. The F200 / F201 has four 10/100 MBit ethernet ports on its backside. Also on the backside are the serial DB9 Console connector, two USB ports, two PCI slots, and, only on the F201, the WiFi antenna connector. [. . . ]