User manual BECKER 4720 TRAFFIC PRO UPDATECD3 6

[. . . ] If more than 20 locations share the same post code, the display will show the location input menu instead of the abovementioned list. In that case, the location name is to be entered as described in , , Entering the destination". If there are no streets in the selected town or only the centre can be selected, the unit will switch directly to the route menu. " The display then shows either the destination corresponding to the post code or, if the post code is shared among several towns, a list containing these towns. 6HOHFWLQJ GHVWLQDWLRQ YLD SRVW FRGH The destination can also be selected via the town's post code. ! ! by turning the right rotary control and press to confirm the selection. ! [. . . ] Press the left rotary control to display information on the point of interest. This information may include prices, location description, general appraisal etc. , for the point of interest. "! !! With the right rotary control, select either !!. or !  !# OHM q After a short time, the available points of interest for the selected categories are displayed. Pressing 1DY or pressing the left rotary control , returns to the list of points of interest. Following selection of the point of interest, you are prompted to insert the navigation CD for route calculation. If the point of interest was selected during active navigation, it will be treated as a stopover. Subject to errors and technical modifications 22 Copyright by Becker GmbH, D-76303 Karlsbad 1DYLJDWLRQ &' ; After a short time, route calculation to the selected point of interest is performed. 1RWH If a stopover has already been entered, it will be overwritten by the new point of interest. In order to cancel navigation to the selected point of interest, you must either cancel navigation or cancel navigation to the stopover, as described in the complete operating guide. In order to cancel entry of the point of interest from the point of interest (P. O. I. ) CD, you must eject the point of interest (P. O. I. ) CD by pressing . 7HUPV RI OLFHQFH You are granted a non-exclusive licence to use the database for your personal purposes, or, where applicable, for internal purposes in your business operations. It is forbidden to extract or make further use of significant parts of the database content, or to duplicate, copy, modify, adapt, translate, analyse, decompile or reverse engineer any part thereof. Under no circumstances do we accept any liability. , QIOXHQFLQJ WKH FDOFXODWLRQ RI (7$ "!"! "! Select and confirm tings menu. in the system set- (7$ stands for (stimated 7ime of $rrival. !& $p Use the right rotary control · !& to select the desired setting. With this setting the unit adjusts ETA for faster drivers. It offers a sufficiently accurate calculation of ETA for most drivers. Subject to errors and technical modifications 23 Copyright by Becker GmbH, D-76303 Karlsbad 1DYLJDWLRQ &' ; · $p · ! With this setting the unit adjusts for drivers who may take longer for the planned journey. The system returns to the system settings menu. The display shows the current time. The system returns to the system settings menu. 6HWWLQJ WKH WLPH GLVSOD\ !in the system settings menu. Y #Y ! ! Use the right rotary control · · Y #Y ! to select the desired setting. The display shows the remaining travel time. ! The display shows the estimated time of arrival. Subject to errors and technical modifications 24 Copyright by Becker GmbH, D-76303 Karlsbad 1DYLJDWLRQ &' ; '\QDPLF QDYLJDWLRQ ZLWK 70& 1RWH Dynamic route guidance is not possible in all countries. To use dynamic navigation and the functions described below, TMC must be switched on, as described under "Switching TMC on/off" on page 30. When any route recalculations are made with active dynamic route guidance, the navigation system may request the Navigation CD (if the Navigation CD is not already inserted). 1RWH Can only be selected if TMC has been switched on or is currently switched on. See "Switching TMC on/off" on page 30. # !! D F F " Y If !!S&Y !!S !Y), then & must be selected by entering the route settings. Y Y :KDW LV G\QDPLF URXWH JXLGDQFH" Dynamic route guidance is used to calculate the route, taking current traffic announcements into account. The traffic announcements are transmitted by a TMC radio station in addition to the radio programme and are received and analysed by the navigation system. [. . . ] If TMC is switched on, a traffic programme transmitter cannot be selected freely. This transmitter then corresponds to the traffic programme transmitter. If TMC is switched off, a traffic programme transmitter can be selected freely. 1RWH Dynamic navigation functions (dynamic route, traffic information) cannot be selected or called up. Using the right rotary control , select <;6:, 3, *; and press to confirm. [. . . ]