User manual CASABLANCA FAN COMPAGNY WAILEA
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CASABLANCA FAN COMPAGNY WAILEA. We hope that this CASABLANCA FAN COMPAGNY WAILEA user guide will be useful to you.
Manual abstract: user guide CASABLANCA FAN COMPAGNY WAILEA
Detailed instructions for use are in the User's Guide.
[. . . ] For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
· The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons. · Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer. · It is always a good idea to have an assistant to help with the installation. [. . . ] Before discarding packaging material, be certain that all parts have been removed.
3mm ALLEN WRENCH
DOWNROD & BALL ASSEMBLY
FAN PREPARATION
CAUTION: Before trimming wires or installing the downrod, pull the wires on the bottom of the fan to assure they are all the same length as shown.
MOTOR WIRES
BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY
IMPORTANT SAFETY INFORMATION!
Prepare for fan installation as follows: Step A. Route the wires from the motor through the Perma·LockTM downrod and ball assembly. Tip: The downrod has a tapered thread that is designed to lock completely when correctly installed. Using the provided allen wrench, loosen the set screw several turns to allow installation of the downrod. Thread the downrod into the motor coupling until it stops turning, this will take at least four and a half full turns. Securely tighten the set screw with the provided allen wrench to ensure safe operation of your fan. CAUTION: Failure to fully lock in the downrod before securely tightening the allen set screw may cause the fan to separate from the downrod during normal operation!
GROUND WIRE
DOWNROD & BALL ASSEMBLY
ALLEN SET SCREW
TAPERED THREAD
MOTOR COUPLING
3
WAILEA
CROSSBAR MOUNTING BRACKET
TM
CEILING HARDWARE
ADDITIONAL HARDWARE WIRE NUT (4) 21/4 x 8-32 ROUNDED HEAD SCREW (2) 1 x 8-32 ROUNDED FLAT WASHER (2) HEAD SCREW (2)
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Warning:Toreducetheriskof fire, electricalshock, or personal injury, mount to outlet box marked acceptableforceilingfansupportusingthemounting hardware provided with the outlet box. Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked `Approved for ceiling fan mounting'. If it is not, a new box must be installed.
CROSSBAR MOUNTING BRACKET INSTALLATION
WARNING: Damp Location rated fans require a Ground Fault Interrupter (GFI). Use a weather-proof outlet box, properly connect ground wires, and use only under a weather-proof structure.
CEILING FAN APPROVED OUTLET BOX
Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Using the screwdriver, tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening.
CEILING WIRING CROSSBAR MOUNTING BRACKET FLAT WASHER
RIDGE SIDE DOWN
CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket.
GREEN GROUND WIRE
OUTLET BOX MOUNTING HARDWARE
CANOPY HARDWARE
CANOPY SCREW (4)
CANOPY HATCH
CANOPY
CANOPY LOCK WASHER (4)
4
WAILEA
CANOPY INSTALLATION
Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. Note: On sloped ceilings, align the canopy opening toward the top or room peak.
CROSSBAR MOUNTING BRACKET INSTALLED
TM
CANOPY
CANOPY LOCK WASHERS
CANOPY SCREWS
HANGING THE FAN
Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. Note: The fan weight is 11 lbs.
CAPPED BLUE D1-OPTION WIRE.
BALL
SLOT PIN
CANOPY ELECTRICAL CONNECTIONS
Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. Pull Chain Connections · GREEN leads from mounting plate and fan to GROUND conductor of power source. [. . . ] Changing Light Bulbs Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs. Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty.
BREAK-IN PERIOD DOES NOT RUN ON LOW SPEED
Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. Check the screws holding the blade holders to the flywheel (or direct drive motor). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CASABLANCA FAN COMPAGNY WAILEA
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CASABLANCA FAN COMPAGNY WAILEA will begin.