User manual CAT EYE CC-6000 (MICRO)

[. . . ] (In the total distance display mode, the current wheel circumference (A) or (B) is shown. ) MAIN UNIT PREPARATION B AT User must make the following setting according to instructions before the cyclocomputer can be used properly. Fig. 7 1. How to measure the exact Wheel Circumference (L)(Fig. 3) First, adjust tire pressure and then put a mark on the tire tread and the ground simultaneously. Mark the ground at the end of one revolution and then measure the distance between the two marks. Or, the "Setting Values Cross Reference Table" can help you to find out an approximate wheel circumference according to tire size. bracket Specifications Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] No Contakt Magnetic Sensor Cordless Système . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Directional electromagnetic induction Operating Temperature Range/ . . . . . . . . . . . . . . . . . Setting the Speed Scale (Fig. 4) When the AC button is pressed and all displays illuminate then the "mile/h" appears as shown in fig. 4. "km/h" and "mile/h" are displayed alternatively each time the right button is pressed. Select any speed scale as desired and press SET button to complete the setting. LIMITED WARRANTY 2-Year Warranty: Only Main Unit/Sensor If trouble occurs during normal use, the part is repaired or replaced free of charge. When returning the product for CATEYE warranty service, pack it very carefully, and enclose the warranty certificate and instructions for repair. Please make sure to write or type your name and address clearly on the warranty certificate, so that the product can be shipped back to you as soon as the necessary repair/adjustment is completed. Insurance, handling and transportation charges to our service shall be borne by person desiring service. Address for service 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn. : CATEYE Customer Service Section Service & Research Address for United States Consumers: CATEYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone: 303-443-4595 Toll Free: 800-5CATEYE Fax: 303-473-0006 e-mail: CatEyeUSA@aol. com Fig. 9 lever bracket rubber pad slide 3. Setting the Wheel Circumference (Fig. 5. 6) Fig. 10 This cyclocomputer is able to memorize two different wheel circumferences. Cut the excess sensor zone Fig. 16 sensor band B with scissors or the like. SENSOR with TRANSMITTER SENS OR ZONE magnet Check points for sensor mounting: 1. The triangle mark on the sensor shall aim at the main unit. #169-6070 Wheel Magnet #166-5150 Lithium Battery (CR2032) Fig. 17 spoke COIN TEST Mount the main unit on the bracket. If current speed doesn't appear on the sensor zone main display, press either left or right button to release the unit from the power about 5mm saving mode. Then spin the front wheel to make sure the wheel sensor pulse symbol flickers. If it does not flicker, adjust the position of sensor until it flickers magnet normally. The mounting is completed and the cyclocomputer is operational. THE CORDLESS SYSTEM spoke Fig. 18 Fig. 19 OPEN The sensor picks up wheel revolution signal and transmits the signal to the receiver in the main unit. The approximate service hour of batteries is as follows: The main unit (receiver): --- Approx. 2 years (average 1 hour's use per day) The sensor (transmitter): ------- Total distance of approx. 10, 000 miles (16, 000 km) sensor Note: To prevent external signal interference, the sensor signal reception range is restricted. For best performance, the triangle mark on the sensor shall aim at the direction to the main unit. The distance between the sensor and main unit must be kept within 45 cm. [. . . ] The battery service hours quoted above is the average for a 45cm distance between the sensor and main unit. · The cordless system may be interfered with in the following situation, so that main unit may display false data. Riding in places where intensive electromagnetic wave or field exist, such as TV transmission station and radar installations. When two bicycles carrying similar cyclocomputers are ridden side by side. REPLACING THE BATTERIES Fig. 20 CLOSE OPEN CR2032 Batteries are already loaded in the main unit and the sensor. How to replace battery in Main Unit (Fig. 20) Open the battery cover on the back and insert a new CR2032 (lithium) with the (+) pole upward, while pressing the side of the battery against the contact. [. . . ]