User manual CATEYE MSC 3DX

[. . . ] Just attach the 3Dx attachment on your bracket. PUSH 3Dx attachment 2 Attaching Chest Belt and Main Unit 3 Setting up Main Unit 4 Other Important Features For more detailed setup and operations, please read the user manual. E 2-8-25, Kuwazu, Hihashi Sumiyoshi-ku, Osaka 546-0041 Japan Service & Research Address for United States Consumers: CAT EYE Service & Research Center 1705 14 th St. 115 Boulder CO 80302 Phone: 303-443-4595 FAX: 303-473-0006 Toll Free: 800-5 CAT EYE URL: http://www. cateye. com -1- Pay attention to the positions of the sensors and the magnets. 1 Parts Installation Parts Names Make sure that the following parts are included in the package. 1 2 3 4 5 6 Bracket (Includes 3Dx attachment) Speed Sensor (Short cord) Cadence Sensor (Long cord) Sensor Band A (L/S) Sensor Band B Nylon Ties 7 8 9 0 q w Sensor Rubber Pad Bracket Rubber Pad Bracket Rubber Pad with Holder Screw Wheel Magnet Cadence Magnet 3Dx attachment 1 7 4 5 8 2 3 Entire View 10 11 12 9 6 Important A The clearance between the sensors 23 and the magnets qw should be about 5mm. B Align the center of the magnets qw and the sensor's marking line while rotating the wheel or crank. Caution: Attach the sensor and the magnet within 10cm from the hub axle. marking line Speed Sensor and Wheel Magnet Cadence Sensor and Cadence Magnet within 10cm Speed Sensor and Wheel Magnet Cadence Sensor and Cadence Magnet -2- Magnet & Sensor ! [. . . ] Be sure to attach electrode area of the chestbelt to your skin closely. Reference: If you wear the chestbelt indirectly on the skin, moisten the electrode area for the best results. Dry skin will cause measurement error in winter, even if the chestbelt is attached to your skin directly. Adjust the chestbelt so that the transmitter is placed at the front of your chest (under breast). Wear the chest belt heart rate sensor in the legible way (the top mark on the transmitter should come to the top). 1 Attachment Belt 2 Electrode Belt 3 Transmitter MainUnit Mount: 1. Caution: When riding, do not touch the lever; the main unit might fall off. Remove: To remove the main unit, unwind the wristband and push the lever. -4PUSH Hook How to mount the unit to bicycle Release Lever Remove Release Lever Input the wheel circumference of your bicycle into the main unit. Find out your bicycle's wheel circumference from the table below. If you cannot fine one, use the default figure " 2096" temporarily. Name of Button The tire size is marked on the side of your tire. Wheel Circumference = L 3 Setting up Main Unit wheel circumference !-1 (1) Initial Setting Select a Speed Scale The main unit has 6 buttons: SET/AT button, MODE button, LAP button, LT button, S/S button and AC button. Push the MODE button to switch between "km/h" and "mph". Input your bicycle's wheel circumference obtained from the above table. (To increase/decrease rapidly, hold down the respective button. ) Caution: This is just the temporary setting of the wheel circumference. When you want to change wheel circumference later, refer to "Changing wheel circumference" in page 13 of the user manual. Push SET/AT button to fix the setting, and the screen shows "Current Speed " in the upper display, "Heart Rate " in the middle display and "Elapsed Time TM" in the lower display (!Initial setting is completed. !-4 !-3 "Elapsed Time TM" Tire Size 24 x 1 24 x 3/4 Tubular 24 x 1-1/8 Tubular 24 x 1-1/4 24 x 1. 75 24 x 2. 00 24 x 2. 125 26 x 1 (559mm) 26 x 1 (650C) 26 x 1. 25 26 x 1-1/8 Tubular 26 x 1-3/8 26 x 1-1/2 26 x 1. 40 26 x 1. 50 26 x 1. 75 26 x 1. 95 26 x 2. 00 26 x 2. 10 26 x 2. 125 26 x 2. 35 27 x 1 27 x 1-1/8 27 x 1-1/4 27 x 1-3/8 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 44C mm 1753 1785 1795 1905 1890 1925 1965 1913 1952 1953 1970 2068 2100 2005 1985 2023 2050 2055 2068 2070 2083 2145 2155 2161 2169 2090 2125 2105 2070 2090 2086 2096 2105 2136 2170 2155 2130 2168 2180 2224 -5- (2) Basic Operations Start and stop measurement Push S/S button and the unit will start measuring "Elapsed Time TM". At the same time, calculation of "Trip Distance DST" and "Average Speed AVS" starts. "Current Speed "Cadence Switching Functions ", "Heart Rate ", ", "Total Distance ODO", "Maximum Heart Rate MXP" and "Maximum Speed MXS" continue to be measured and displayed regardless of the start/stop. In The upper display always shows "Current Speed the lower display, the selected function is displayed. As illustrated below, the lower display changes as TM (Elapsed Time) ­> Cadence C ­> Clock ­> AVS (Average Speed) ­> Dst (Trip Distance). These five functions are called "Main functions", and each Main function has its corresponding Sub function. [. . . ] However, you can change it to Clock or Cadence , by pressing SET/AT button and S/S button simultaneously. If Clock comes up to the upper display, Current Speed comes down to the lower display and joins in the main function; in the same manner, if comes up, Current Speed comes down. Cadence *When Auto function is on, just push S/S button and the upper display changes from "Current speed " to "Clock time " or "Cadence ". Reset Operation Press Simultaneously To reset the data of "Elapsed Time TM", "Average Speed AVS", "Maximum Speed MXS", "Maximum Heart Rate MXP" and "Trip Distance DST", push S/S button and MODE button simultaneously. Pace Arrow When you are using the unit for cycling, the pace arrow appears in the right side of the lower display. The pace arrow indicates whether the current speed is higher or lower than the average speed. [. . . ]