User manual CDA RV1000

[. . . ] RV 1000 . . GB Users Operating Instructions Installation instructions Before operating this cooker, please read these instructions carefully Dear Customer Thank you for choosing one of our appliances, carefully designed and built by our specialist staff and thoroughly tested to satisfy your cooking requirements. We suggest that you read this Instruction Booklet so that you will understand fully how to operate your appliance. CDA IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. [. . . ] Keep children away. Rotisserie The oven is equipped with a rotisserie. This device is made up of: ­ an electrical motor mounted on the rear part of the oven ­ a stainless steel rod, equipped with a detachable athermic grip and 2 recordable forks ­ a rod support to be inserted into the central rack holders of the oven. Use of the rotisserie ­ Insert the dripping pan into the lowest rack holders of the oven and insert the rod support into the intermediate rack holders. ­ Put the meat to be cooked onto the rod, being careful to secure it in the center with the special forks. ­ Insert the rod into the motor opening and rest it onto the support of the spit collar; then remove the grip by turning it to the left. The rotation direction of the rotisserie can be either clockwise or counter-clockwise. Fig. 13 22 Use of special dish rack This special shelf can be used as dish rack or turning over, as normal shelf for oven cooking. It must be inserted between the guides of the lateral racks. Using the special shelf as a dish rack Slide in the shelf on the guides, on the lower level of the lateral racks. The prongs where the plates are to be inserted, must be turned upwards. The shelf must be fitted so that the safety catch, which stops it sliding out, faces the bottom of the oven (see detail of figure 14). To facilitate this operation, pull the special rack up to the safety lock. It is advisable to handle the plates using oven gloves. Using the special rack for normal cooking Slide in the shelf on the guides: the safety catch must be turned toward the oven base (see detail of figure 15). The flat surface can be used to put cooking pans or food directly on the rack - the dripping pan should be placed under the rack to catch the cooking juices and fats. Fig. 15 23 Do's and do not's Do's and do not's · Do always grill with the oven door closed. · Do read the user instructions carefully before using the cooker for first time. · Do allow the oven to heat for one and a half hours, before using for the first time, in order to expel any smell from the new oven insulation, without the introduction of food. · Do always use oven gloves when removing food shelves and trays from the oven. · Do not allow fat or oils to build up in the oven trays, or oven base. · Do not place cooking utensils or plates directly onto the oven base. · Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in contact with enamel parts (inside the oven and on the oven tray). · Do not use abrasive cleaners or powders that will scratch the surface of the stainless steel and the enamel. · Do not attempt to repair the internal workings of your cooker. Do not store flammable material in the ovens and in the storage compartment (RV 900 . . [. . . ] The manufacturer declines all responsability for any inconvenience resulting from the inobservance of this condition. 48 Electrical feeder cable connection To connect the supply cable: - Remove the screws securing the cover "A" on the rear of the cooker (fig. The supply cable must be of a suitable size for the current requirements of the appliance; see the section "Feeder cable section". - Connect the wires to the terminal block "B" as shown in the diagram in figure 39; or connect the phase wires to the terminal block "B" and the earth wire to the terminal PE as shown in figure 38. - Take up any slack in the cable and secure with the cable clamp "D". [. . . ]