User manual CHANEY INSTRUMENT NEWER MODEL 00754 WIRELESS WEATHER STATION AND ATOMIC CLOCK WITH REMOTE SENSOR

[. . . ] To Select Alarm Modes: Slide the alarm switch to: OFF: Alarm Off Bell: Daily alarm- no snooze function(press the "SNOOZE/LIGHT" button to stop the alarm for 1 day) Zz: Snooze Alarm (press the "SNOOZE/ALARM" button for 10 minute snooze, press any button to stop the alarm for one day) MAIN UNIT Manual Setting for Time: 1. To set the clock manually: hold the "SET" button and press "HR" to adjust the hour, "MIN" to adjust the minutes. To set the calendar manually: Hold the "DATE" button for 3 seconds and use the "MINUTE" (-) and "HOUR" (+) buttons to adjust up and down. The year will begin to flash; adjust to the correct year and press "DATE" to confirm. [. . . ] The time zone icon is located to the right of the tower icon on the main display. P = PACIFIC STANDARD TIME M = MOUNTAIN STANDARD TIME C = CENTRAL STANDARD TIME E = EASTERN STANDARD TIME 5. Use a pen to push the "C/F" button To select between Fahrenheit or Celsius temperature display on the main unit. The "C/F" button is located on the lower right corner on the back of the main unit. NOTE: The main unit will reject any manual settings when it is automatically searching for the temperature and time settings. Setting up additional sensors: (Additional sensors can be purchased separately, Acu-rite model #00955) To add an additional sensor, make sure the batteries are in the main unit first, then place batteries in the additional sensor and press the "TX" button on the back of the sensor. The main unit will automatically search for an open channel to register the signal on the main unit. Auto Scroll: If additional sensors are used, the auto scroll feature will display each channel's temperature for 5 seconds. To activate the auto scroll feature, press the "channel" button until the arrow icon appears on the temperature screen. Additional Remote Sensor Placement Suggestions: Additional sensors can be purchased separately, Acu-rite model #00955 About The Wireless Thermometer Min/Max Temperature Memory: Press the "MIN/MAX" button to view the maximum values for 5 seconds, press again to view minimum memory values. When the "MIN/MAX" button is pressed, the time that the minimum and maximum temperatures were recorded within a 24-hour time period will display. Temperature Trend Indicator: The 3 arrow icons will indicate Rising, Steady, or Falling if the temperature change is more than 1 degree an hour. A snowflake icon will appear on the main display if the temperature reaches 32ºF / 0ºC or below. The Trend icons will appear to the right of the remote sensor temperature readout on the main display. Battery Replacement: A low battery icon will appear when the main unit or the sensor needs new batteries. For the main unit, the icon will appear next to the indoor temperature readout on the main display. For the remote sensor unit, the icon will appear next to the remote temperature readout on the main display. NOTE: When replacing batteries in the main unit, the batteries in all remote sensors must be removed and re-installed according to the initial set-up process. When replacing the batteries in the remote sensor only, the channel on the main unit must be cleared. This can be achieved by selecting the appropriate channel and pressing the "CHANNEL" button for 3-5 seconds. Place new batteries in the remote sensor and then follow the quick setup guide above. · Outside your home or place of business · Wine cellars · In the garage · Childrens room · Gardens or greenhouses · Any location that remote temperature readings are beneficial About The Atomic Clock The main unit has a special receiving device that picks up an AM radio signal broadcasted by the National Institute of Standards and Technology (NIST) in Fort Collins, Colorado. atomic clock that is the most accurate timekeeping device in the world! [. . . ] In most cases, the unit will re-sync with the remote sensor on it's own. It may also help to bring the remote sensor closer to the main unit to re-sync the main unit and the remote sensor. However, should this condition continue to occur, be sure to check the following: A. The sensor may be placed outside of the effective transmission range (100 feet). [. . . ]