User manual CHICCO SCOOP NACELLE

[. . . ] WARNING: before assembly, check that the product and all of its components have not been damaged during transportation. Should any part be damaged, torn or missing, do not use and keep out of reach of children. WARNING: This product is only suitable for a child who cannot sit up unaided or to turn and stand up helping themselves with their hands and knees. WARNING: Do not let other children play unattended close to the carrycot. [. . . ] WARNING: When used as a pram body, remember that: · The depth of the pram body measured frrom the top of the mattress to the top of the side of the body at, or at any position within 300mm from, the harness attachment points, should not be Reduced to less than 140mm when the mattress is in position; · Routinely wipe clean plastic parts with a soft damp cloth. Always dry the metal parts to prevent the formation of rust if the carrycot has come into contact with water. Maintenance Lubricate the moving parts only if necessary, with a light application of a silicone based lubricant. To avoid friction, ensure that the locking devices of the carrycot and pram are free from dust or sand. Do not leave the product exposed to the sun for a long period of time; it may cause the fabric to fade. CARRYCOT FEATURES HOOD The carrycot is equipped with a sun canopy and windbreaker that can be adjusted to various positions. mOUNTING AND REMOVAL 1- Check that the clips located on the end of the metal arch are properly fastened to the buttons located on the fabric part. The buttons are properly fastened if the two ends of the metal arch (fig 1) are easily visible. 2- Insert the two metal ends in the B and C supports located in the central part of the carrycot until you hear a click (figure 2A); fasten the four tabs of the rear arch (figure 2 B). NB: The coupling system is located inside the plastic B and C supports, the round button on the supports serve only for removing the hood (see point 3). 3- To remove the hood, first pull out the 4 tabs of the rear arch (figure 3A) and then remove the front arch by pushing the two buttons located HOW TO USE THE HOOD 4- Inside the hood, between the visor and the first segment, is a fabric ring that can be used for hanging soft toys. Warning- only use toys that have the following Chicco codes: 71328, 71329, 71330. There is an adjustable rear opening flap to guarantee proper ventilation: Unzip it to open, and fold the fabric panel on the upper part of the hood. INTERNAL COVERING AND COVER 5- To fasten the internal covering to the carrycot: Slip the plastic band located in the baby's head zone between the styrofoam support and the body of the carrycot; then fasten the two tabs in the baby's foot area under the edge of the carrycot, as shown in figure 5A. Then fasten the two lateral press studs and fasten the two fabric strips with velcro in the centre of the area where the baby's feet are (figure 5 B). Once mounted, both sides may be opened, or on the top using the velcro opening (figure 5 C). aDJUSTABLE BACKREST COMFORT SYSTEM 6- The backrest of the carrycot can be adjusted gradually. To lift or lower the backrest use the wheel located on the outer part of the carrycot near the baby's feet (figure 6). [. . . ] The baby's feet end of the carrycot should be clos- 13- Align the pins on the two sides of the carrycot with the openings located on the arms of the stroller (figure 13 A), then carefully set down the carrycot until you hear the lock click (figure 13 B). WARNING: Before using, make sure that the carrycot is properly locked on by pulling on it upwards. REMOVING THE CARRYCOT 14- Bring the handle to its vertical position (transport mode) until you hear a click which means it is locked in place (figure 14). 15- Push the button located on the front part of the baby carriage (figure 15 A), therefore, keeping the button pressed; lift the carrycot off of the structure (figure 15 B). [. . . ]