User manual CISSELL CF 448

[. . . ] 6 ntlain Setting Control Mode Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8 O e a i gI s r c i n p r t n n t u t o s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 at hes Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Page 3 FOR YOUR SAFETY Always shut off or disconnect power to the conveyor before servicing. [. . . ] Always shut off or disconnect power when performing maintenance or adjustment work. Post operator instructions and safety warnings in a prominent location. SPECIFICATIONS Input power: 24VAC Six position memory Dual display: current position, desired position Range: 1-9999 positions Second range available for double deck conveyors Automatic coast Set-up parameters input from the keyboard Page 4 DESCRIPTION This control operates one garment conveyor. It allows the attendant to automatically bring any position on the conveyor to the unloading area by entering the position number into the control's memory and initiating the search operation. Features: ·Memory can hold up to six positions at one time ·Dual display shows CURRENT POSITION and DESIRED POSITION ·Range 1-9999 positions ·Second range available for double deck conveyors ·Jog buttons on control panel ·Pause button (interrupts search operation) ·Calibrate current conveyor positions from control panel ·One shaft encoder works with all conveyors ·"Pick as entered" / "Shortest route" options ·Auto-coast ·Abnormal speed detection ·Set-up parameters entered into the control's memory from the keyboard. Page 5 DESCRIPTION OF CONTROL PANEL 1. Resets the control after an emergency EMERGENCY STOP. Turns power off to control box. Stops conveyor. 3. Shows the current position of the conveyor or the number being entered on the keyboard. Will manually run the conveyor in the direction indicated on the button as long as the button is depressed. Used in conjunction with a keyboard entry and the SHIFT key to input the current position. Clears current entry shown on the CURRENT POSITION/ENTRY display if pressed by itself or if pressed with the SHIFT key, clears the memory of all positions previously entered. Loads a position into memory after it had been entered on the keyboard. The NEXT DESIRED POSITION DISPLAY will flash to indicate if the conveyor is in the paused state. Should the power be off for a longer period of time, the parameters will have to be re-entered. CURRENT POSITION To "calibrate" the conveyor control to set the current conveyor position at the uploading point, key in the current position and press SHIFT + SET. The top display should now show the position that is at the unloading point. Turns "beep" on Turns "beep" off Selects "shortest route" option Selects "pick as entered" option Displays software version (SHIFT-CLR cancels) Page 9 OPERATING INSTRUCTIONS Before operating the conveyor, the conveyor parameters must be entered into the control and the "current position" set. To automatically seek positions on the conveyor, enter the desired position on the keyboard (it will show on the upper display). If the entry is correct, press the ENTER key to enter the position into the memory. These can be entered all at once or at any other time even while the conveyor is in the precess of seeking a position. Once a position is brought to the unloading point, it is automatically removed from the memory. Should incorrect positions be entered into the memory, SHIFT+CLR will remove ALL positions from the memory. The next position that the conveyor will seek is shown in the lower display. The order that the conveyor places the entered positions into the memory depends on which option ("pick as entered" or "shortest route") was selected. [. . . ] If "pick as entered" was selected, the order of the positions in the memory will be the same order as they were entered. If "shortest route" was selected, the control will order the positions in the memory so that the conveyor will travel the shortest distance (shortest time) to reach all of the positions in the memory. When the position is brought to the unload point the conveyor will stop. Pressing the PAUSE button will interrupt the seek operation and stop the conveyor. [. . . ]