User manual CISSELL CF 45

[. . . ] Do not touch any electrical switch; do not use any phone in your building. If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. WARNING: In the event the user smells gas odor, instructions on what to do must be posted in a prominent location. WARNING: Purchaser must post the following notice in a prominent location: FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] In both steam supply and steam return line, it is recommended that each have a 3/4" union and 3/4" globe valve. This will enable you to disconnect the steam connections and service the dryer while your plant is in operation. Before connecting trap and check valve to dryer, open globe valve in steam supply line and allow steam to flow through dryer to flush out any dirt and scale from dryer. After flushing system, install bucket trap (with built-in strainer) and check valve. For successful operation of dryer, install trap 18" below coil and as near to the dryer as possible. Inspect trap carefully for inlet and outlet markings and install according to trap manufacturer's instructions. If steam is gravity returned to boiler, omit trap but install check valve in return line near dryer. Install union and globe valve in return line and make final pipe connections to return header. Page 18 Steam Piping Installation (Illustration) Page 19 Dryer Installation With Multiple Exhaust For Exhaust Duct less than 14 feet (5 m) and 2 elbows equivalent and less than 0. 3 inches (. 8 mbar)static pressure. DRYER EXHAUSTS Area of section "A-A" must be equal to the sum of dryer exhaust pipes entering multiple exhaust pipe. of Dryers Duct Diameter (in inches) (in CM) HD30SL 123 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 8 12 14 16 18 20 22 23 24 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 20 30 35 41 46 51 56 58 61 66 68 71 73 76 78 81 84 86 89 91 94 97 99 100 Exhaust Booster Fan Power Supply to Fan ____ ____ ____ ____ ____ ____ Relay Coils Start and Stop Switches on Dryers Page 20 Dryer Installation with Multiple Exhaust DRYER INSTALLATION WITH MULTIPLE EXHAUST For Exhaust Duct more than 14 feet (5 m) and 2 elbows equivalent and more than 0. 3 inches (. 8 mbar) static pressure. Make-up air from outside building may enter enclosure from top or side walls. (See Dryer Make-Up Air Chart on page 22) Use constant diameter duct with area equal to the sum of dryer duct areas. In summary, there must be the proper size out-of-doors inlet air opening and an exhaust duct, size and length of which allows flow through the dryer with no more than 0. 3 inches water column (. 8 mbar) static pressure in the exhaust duct. In some instances, special fans are required to supply make-up air, and/or booster exhaust fans are required. Exhaust duct maximum length 14 feet (5 mm) of straight duct and maximum of two 90° bends. Use clean-outs in the exhaust duct and clean periodically when needed. Never exceed 0. 3 inches water column (. 8 mbar) static pressure in the exhaust duct. Make-up air from outside the building may enter the enclosure from the top or side walls. Use barometric shutters in the inlet air opening to control air when dryers are not running. EXHAUST DUCT MAKE-UP AIR OTHER RECOMMENDATIONS TROUBLESHOOTING Other Recommendations To assure compliance, consult local building code requirements. Troubleshooting Hot dryer surfaces, scorched clothes, slow drying, lint accumulations, or air switch malfunction are indicators of exhaust duct and/or make-up air problems. Page 24 Rules for Safe Operation of Dryer RULES FOR SAFE OPERATION OF DRYER 1. Be sure your dryer is installed properly in accordance with the recommended instructions. CAUTION Be safe--shut main electrical power supply and gas supply off externally before attempting service. CAUTION Never use drycleaning solvents: gasoline, kerosene, or other flammable liquids in the dryer. [. . . ] TUS15105 TU15105 1 1 2 3 4 5 6 7 8 TUS15068 TU15068 TU15087 SB-00965-0 TU7006 VSB130 TU2814 TU15140 C249 Description Basket & Spyder Asm. Screw-button cap 5/16 - 18 Shim Washer cut 5/16 5/16" Lock washer Tie rod, 5/16-18 31-3/4" Nut 5/16" - 18 Page 47 REAR VIEW Ref. 1 2 3 4 5 6 TU14725 TU15030WH TU15150 TU15151 TU7733 TU15671 Description Cover plate Jacket (white) Upper rear cover Lower rear cover Screw self drilling 8-18 x 1/2" Air switch cover Page 48 AIR SWITCH ASSEMBLY - TU8206 Ref No. F888 TU1770 TU1771 TU2463 TU3219 TU3476 TU7733 TU8155 TU8171 Description E-RING INSULATOR #6 TINNERMAN NUT ACTUATOR ARM #6 x 1 S. M. S. [. . . ]