User manual CISSELL CF 487

[. . . ] - Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. Do not touch any electrical switch; do not use any phone in your building. If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. WARNING: In the event the user smells gas odor, instructions on what to do must be posted in a prominent location. WARNING: Purchaser must post the following notice in a prominent location: FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] PRESSURE In figuring total length of pipe, make allowance for tees and elbows. (50 ft. ) (75 ft. ) (100 ft. ) (125 ft. ) 15, 24 m 22, 86 m 30, 48 m 38, 1 m 3/4 3/4 3/4 1 1 1 1 1 1 1/4 1 1/4 1 1/2 1 1/2 2 2 2 2 2 2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3 3 3 3 3 3 3 1/2 3 1/2 3 1/2 3 1/2 3/4 3/4 1 1 1 1 1 1 1/4 1 1/4 1 1/2 1 1/2 2 2 2 2 2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3 3 3 3 3 3 3 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 3/4 1 1 1 1 1 1/4 1 1/4 1 1/4 1 1/2 1 1/2 2 2 2 2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3 3 3 3 3 3 3 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 4 4 3/4 1 1 1 1 1 1/4 1 1/4 1 1/4 1 1/2 1 1/2 2 2 2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3 3 3 3 3 3 3 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 4 4 4 4 (150 ft. ) 45, 72 m 3/4 1 1 1 1 1/4 1 1/4 1 1/4 1 1/2 1 1/2 2 2 2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3 3 3 3 3 3 3 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 4 4 4 4 4 4 60, 000 80, 000 100, 000 120, 000 140, 000 160, 000 180, 000 200, 000 300, 000 400, 000 500, 000 600, 000 700, 000 800, 000 900, 000 1, 000, 000 1, 100, 000 1, 200, 000 1, 300, 000 1, 400, 000 1, 500, 000 1, 600, 000 1, 700, 000 1, 800, 000 1, 900, 000 2, 000, 000 2, 200, 000 2, 400, 000 2, 600, 000 2, 800, 000 3, 000, 000 3, 200, 000 3, 400, 000 3, 600, 000 3, 800, 000 4, 000, 000 15000 20000 25200 30200 35200 40300 45300 50400 75600 100800 126000 151200 176400 202000 230000 250000 270000 300000 330000 350000 380000 400000 430000 450000 480000 504000 550000 605000 650000 705000 750000 806000 850000 907000 960000 1000000 Page 22 Steam Piping Installation Instructions STEAM PIPING INSTALLATION INSTRUCTIONS 1. To prevent condensate draining from headers to dryer, piping should have a minimum 12" above respective header. Do not make steam connection to header with a horizontal or downwardly facing tee or elbow. Whenever possible, horizontal runs of steam lines must drain, by gravity, to respective steam header. Water pockets, or an imporperly drained steam header will provide wet steam, causing improper operation of dryer. If pockets or improper drainage cannot be eliminated, install a by-pass trap to drain condensate from the low point in the steam supply header to the return. In both steam supply and steam return line, it is recommended that each have a 3/4" union and 3/4" globe valve. This will enable you to disconnect the steam connections and service the dryer while your plant is in operation. Before connecting trap and check valve to dryer, open globe valve in steam supply line and allow steam to flow through dryer to flush out any dirt and scale from dryer. After flushing system, install bucket trap (with built-in strainer) and check valve. Heat loss into laundry room from dryer front panels is about 60 Btu/h per square foot (15 kcal/h per 0. 1m²). 2. 3. 4. Page 27 Suggested Minimum Dryer Make-up Air Requirements Dryer Model Dryer Pocket Capacity lb kg 30 13. 6 30 13. 6 30 13. 6 50 22. 7 50 22. 7 75 34 75 34 75 34 80 36. 3 110 50 110 50 125 56. 7 150 68 175 79. 4 190 86. 2 20 9. 1 30 13. 6 50 22. 7 75 34 Maximum Air Flow Duct Size For Rate per Pocket Service Connection cfm m3/h inch mm 700 1190 8 203 400 680 6 153 450 765 6 153 800 1360 8 203 450 765 6 153 1000 1700 8 203 536 911 6 153 1000 1700 12 305 1465 2490 10 254 2200 3740 12 305 850 1445 8 203 2000 3400 12 305 2250 3825 12 305 2780 4726 12 305 3000 5100 12 305 450 765 6 153 625 1063 8 203 700 1190 8 203 750 1275 8 203 Required Make-up Air Area per Pocket sq. inch cm2 135 871 77 497 87 561 154 994 87 561 192 1239 103 665 192 1239 282 1819 422 2723 163 1052 384 2477 432 2787 534 3445 576 3716 87 561 120 774 135 871 144 929 C 30 C 30 E/S C 30 ST C 50 C 50 E/S C 75 C 75 E/S C 75 ST HD80 C 110 C 110 E/S C 125 C 150 HD175 HD190 HD20 HD30 HD50 HD75 Notes: 1) The Model C 30 ST has 2 pockets per dryer, each pocket has the above listed characteristics; each pocket is exhausted separately with a 6" (153mm) duct. 2) The Model C 75 ST has 2 pockets per dryer, each pocket has the above listed characteristics; both pockets have one 8" (203mm) exhaust manifolded into one 12" (305mm) exhaust duct for exhaust connection. 3) For the C 30 ST and the C 75 ST Models, the Required Make-up Air Area shown in the table should be doubled since it is shown per pocket, only. 4) E/S indicates an Energy Saving Model. Page 28 Exhaust and Venting DRYER AIR FLOW INSTALLATION Nothing is more important than air flow for the proper operation of a clothes dryer. A dryer is a pump which draws make-up air from the out-of-doors, through the heater, through the clothes and then forces the air through the exhaust duct back to the out-of-doors. Just as in a fluid water pump, there must be a fluid air flow to the inlet of the dryer, if there is to be the proper fluid air flow out of the exhaust duct. In summary, there must be the proper size out-of-doors inlet air opening (4-6 times the combined areas of the air outlet) and an exhaust duct, size and length of which allows flow through the dryer with no more than 0. 3 inches water column static pressure in the exhaust duct. In some instances, special fans are required to supply make-up air, and/or boost exhaust fans are required for both regular and energy saving models. Exhaust duct maximum length 14 feet (4. 3 mm) of straight duct and maximum of two 90° bends. [. . . ] Laundry DryerSingle Motor ModelRear View (Illustration) Models: L36USS36 L36URS36 Gas (Energy-Saver) Gas, Steam or Electric Page 58 Parts75 lb. Laundry DryerSingle Motor ModelRear View 1 TU13111 TU13112 2 SB170 3 TU6263 5 TU8206 6 7 8 9 10 11 12 13 TU5890 TU12576 VSB134 TU4787 TU12642 TU10888 TU5217 TU12803 Jacket Welded (Gas/Electric) Jacket Welded (Steam Models ONLY) Junction Box Cover Screw Air Switch Assembly (see separate page) Control Box Cover Carriage Bolt - 3/8" - 16 x 1" 3/8" Split Lockwasher (Pkg. Idler Bracket with Grease Fitting (Gas Dryers) V-Belt (50 Hz. ) - 4L-600 V-Belt (60 Hz. ) - 4L-590 Rear Guard Complete Right Angle Connector Cable - 42" Long Straight Connector Motor * Key Motor Sheave, 60 Hz. , with Set Screw Motor Sheave, 50 Hz. , with Set Screw Motor Mount W/A Side Gasket Top and Bottom Gasket Felt Seal Key Fan Wheel - 50/60 Hz. of 6) Hex Head Screw - 5/16" - 18 x 3/4" Cut Washer - 5/16" (Pkg. [. . . ]