User manual CISSELL CF 50

[. . . ] - WHAT TO DO IF YOU SMELL GAS · · · · · Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. WARNING: In the event the user smells gas odor, instructions on what to do must be posted in a prominent location. WARNING: Purchaser must post the following notice in a prominent location: FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] Insulate steam supply and return line for safety of operator and safety while servicing dryer. Repair or replace any worn or defective parts. 2. 3. 4. Page 23 Dryer Installation with Multiple Exhaust (Illustration) Page 24 Dryer Installation with Multiple Exhaust DRYER INSTALLATION WITH MULTIPLE EXHAUST For Exhaust Duct more than 14 feet and 2 elbows equivalent and more than 0. 6 inches static pressure. Make-up air from outside building may enter enclosure from top or side walls. For area of make-up air opening refer to "Minimum Dryer Makeup Air Requirments" chart at end of manual. Use constant diameter duct with area equal to the sum of dryer duct areas. EXAMPLE: 6-8 inches diameter duct = (1) 19. 6 inches diameter duct in area. If dryers use room air instead of outside air, the heat loss can be another 25 Btu/h for each cubic foot per minute (cfm) used. Heat loss into laundry room from dryer fronts only is about 60 Btu/h per square foot. See suggested Automatic Electrical Control Wiring Diagram on next page. Fan air flow (cfm) is equal to sum of dryer air flows, but static pressure (SP) is dependent on length of pipe and number of elbows. Barometric Bypass Damper - Adjust to closed flutter position with all dryers and exhaust fan running. Never use dry cleaning solvents: gasoline, kerosene, or other flammible liquids in the dryer. Always keep the lint screen clean; a full lint screen may be a fire hazard. Never use heat to dry items that contain plastic, foam, or sponge rubber, or rags coated with wax or paint. Serious injury will occur if a child should crawl inside and the dryer is turned on. Never use the dryer door opening and top (or the lint drawer) as a step stool. Read and follow manufacturer's instructions on packages of laundry and cleaning aids. Never tumble fiberglass materials in the dryer unless the labels say they are machine dryable. Glass fibers break and can remain in the dryer and could cause skin irriatation if they become mixed into other fabrics. Reference - Lighting and shutdown instructions and wiring diagrams are located on the rear wall of the dryer cabinet. 5. 6. 7. 8. NOTE: It is best to run a properly sized load of rags and/or old towels through one or two cycles prior to drying in service. This process will remove any films or residual coatings left by the manufacturing processes. Page 30 Rules for Safe Operation of Your Dryer CAUTION Synthetic solvent fumes from dry cleaning machines create acids when drawn through the dryer. These acid fumes cause rusting of painted parts, pitting of bright plated parts and completely removes the zinc from galvanized metal parts, such as the tumbler basket. [. . . ] #6-32 x 3/8 Nut, Hex #8-32 Nut, Hex #6-32 Page 59 PROHC SENSOR ASSEMBLY - UPPER and LOWER Ref. TU14724 Description PROHC Sensor assembly (upper) 1 2 3 4 5 6 SB-00952-0 Screw, #6-32x 3/8" long TU14693 Mounting plate upper probe TU14694 Cover plate, probe TU3400 Nut, #6-32 TU7733 Screw, self drill #8-18x 1/2" long 254/00060/00 Humidity sensor UPPER ASSEMBLY Ref. TU15672 Description PROHC Sensor assembly (lower) Bracket (sensor) Switch, 220 degrees Screw, machine #8-32x 1/2" long Screw, #6-32x 3/8" long Nut, hex brass #8-32 Nut, hex brass #6-32 Screw, self drill #8-18x 1/2" long Cover, plate Humidity sensor LOWER ASSEMBLY 1 2 3 4 5 6 7 8 9 CA-13067-0 EA-00411-0 SB-00828-0 SB-00952-0 TU3266 TU3400 TU7733 TU14694 254/00071/10 Page 60 FAN MOTOR ASSEMBLY 1 2 3 4 5 6 7 8 9 10 11 C249 IB140 MTR* OP380 TU14336 TUX640 TUX639 TU1950 TU2007 TU2473 TU2474 TU2814 NUT, 5/16-18 WASHER, 3/8" FLAT SEE MOTOR CHART SCREW, 3/8-16 H. H. WASHER, 5/16 LOCK 12 13 14 15 16 17 18 19 20 21 22 TU3246 TU4706 TU4787 TU5439 TU6723 TUX220 TUX221 TUX342 TUX222 TUX428 TUX429 VSB134 SCREW, 3/8-16 H. H. [. . . ]