User manual CISSELL PUFFIRONEMAN358

[. . . ] The warranty is void on equipment or parts; that have been subjected to misuse, accident, or negligent damage; operated under loads, pressures, speeds, electrical connections, plumbing, or conditions other than those specified by Cissell; operated or repaired with other than genuine Cissell replacement parts; damaged by fire, flood, vandalism, or such other causes beyond the control of Cissell; altered or repaired in any way that effects the reliability or detracts from its performance, or; which have had the identification plate, or serial number, altered, defaced, or removed. No defective equipment or part may be returned to Cissell for repair or replacement without prior written authorization from Cissell. Charges for unauthorized repairs will not be accepted or paid by Cissell. CISSELL MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY, STATUTORY OR OTHERWISE, CONCERNING THE EQUIPMENT OR PARTS INCLUDING, WITHOUT LIMITATION, A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, OR A WARRANTY OF MERCHANTABILITY. [. . . ] Before installing trap and check valve in steam return line, open globe valve in steam supply line to allow steam to flow through machine to flush out any dirt and scale from machine. After flushing system, install bucket trap (with built-in stainer) and check valve as illustrated. For sucessful operation of machine, install trap as close to floor and as near to machine as possible. Inspect trap carefully for inlet and outlet marking and install according to manufacturer instructions. If steam is gravity-returned to boiler, omit trap but install check valve in return line near machine. Install union and globe valve to return line and make final pipe connection to return header. CAUTION: Before operating Puff Iron, open globe valves in steam lines and allow Puff Iron to warm up. When machine is on the end of a line of equipment, extend headers at least 4 ft. Install globe valve, union, check valve trap and optional by-pass of a line. Insulate steam supply and return line for safety of operator and safety while servicing machine. Repair or replace any worn or defective parts. beat the end Page 7 PANEL ASSEMBLY FOR FABRIC PRESSING HEADS Ref. P154 P153 P165 P454 P511 P512 P513 Description Single Table Top 33" Table Top 38" Table Top Table Leg, R or L Front Panel Asm. of 6) * Consists of Front Panel, Cissell Nameplate, screws, and washers. Note: For servicing, new design allows easy access from front of machine by removing front panel screws. Nuts are welded to table leg. Page 8 PANEL ASSEMBLY FOR NON-FABRIC PRESSING HEADS Ref. P637 P631 P634 P638 P632 P635 P639 P633 P636 Description 1-Head Top w/Extension Left & Back 1-Head Top w/Back 1-Head Top w/Extension Right & Back 2-Head Top w/Extension Left & Back 2-Head Top w/Back 2-Head Top w/Extension Right & Back 3-Head Top w/Extension Left & Back 3-Head Top w/Back 3-Head Top w/Extension Right & Back Ref. P454 P511 P512 P513 P509 TU4934 TU2846 TU2847 P274 Description Table Leg, R or L Front Panel Asm. of 6) * Consists of Front Panel, Cissell Nameplate, screws, and washers. Note: For servicing, new design allows easy access from front of machine by removing front panel screws. Nuts are welded to table leg. Page 9 BACKS, CORNERS, EXTENSIONS & BRACES Ref. No. 1 3 4 6 7 8 9 Part No. P155 P158 P159 P167 P161 P166 P189 Description Back Single Table Back Single Table w/Extension Back 33" Double Table Back 38" Triple Back (Used on 33" Table w/Extension) Back (Used on 38" Triple w/Extension 17" Angular Corner Back Ref. No. 10 11 12 13 14 Part No. P157 P156 P192 P484 Description 15 16 17 18 19 20 15" Angular Corner and Back 12" x 12" Sq. [. . . ] To set spring into position, a dimension of about 3/4" should be kept. Reinstall pivot and small lock nut on valve stem as shown on opposite page. Open steam line, allow Puff Iron to heat up and test for leaks. Page 20 CAUTION: When working on Puff Iron Valve Heads. . . Remove "Padded Nylon Covers" from Unpolished Heads. TO REPLACE VALVE SEAT IN PUFF IRON (Figure 1). . . [. . . ]