User manual CITIZEN WATCH U010

[. . . ] Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Names of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching Digital Functions (Modes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EL Illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] * The day is corrected automatically by correcting the year, month and date. Once the date is set, the end of the month is corrected automatically, including leap years. * When the date is set to a date that does not exist, the date will automatically be corrected to the first day of the next month when the watch is returned to the normal display (example: February 30 is automatically corrected to March 1). 16 Alarm On mark (M) The alarm tone sounds for about 15 seconds at the same time every day once it has been set (ON). The alarm can be switched off when it is sounding by pressing any button. City name (B) <Setting Procedure> (A) (1) Press button (M) to switch the watch to the alarm mode. (2) Press button (B) to display the city for which Alarm time On or OF the alarm is to be set. (3) Pressing button (B) continuously for about 2 seconds causes the alarm to be switched ON and the hours to flash. (Pressing button (A) continuously causes the display to advance rapidly. ) (5) Press button (B) to cause the "minutes" to flash. 17 * Since the alarm time is also based on a 12-hour display when the time mode is set to a 12-hour display, pay attention to AM(A) and PM(P) when setting the alarm time. * After the alarm has been set, the alarm time does not change even if the time mode is set to daylight savings time. * When none of the buttons are operated for about 2 minutes in the alarm correction state, the watch automatically returns to the normal alarm display. * When button (M) is pressed in the alarm correction state, the watch immediately returns to the normal alarm display. 10. Using the Chronograph The chronograph is able to measure and display time up to a maximum of 23 hours, 59 minutes and 59. 99 seconds in 1/100 second units. Following completion of measurement for 24 hours, the chronograph returns to the reset display and stops. In addition, the chronograph is also able to measure split time (intermediate elapsed time). [Chronograph Reset Display] Hours (M) (A) Measurement (A) (B) (B) (A) Split time *1 (A) (B) (B) (A) Stops <Switching the Alarm ON and OFF> The alarm is switched On and OF (Off) each time button (A) is pressed during the normal alarm display. When the alarm is set to ON, the " " mark lights on the digital display in each mode. <Sound Monitor> The alarm monitor tone sounds for as long as button (A) is pressed in the alarm mode. 18 Minutes, seconds and 1/100 seconds *1: Automatically returns to the measurement state after 10 seconds. 19 <Measurement Procedure> (1) Press button (M) to switch the watch to the chronograph mode. (2) The chronograph starts when button (A) is pressed and stops when button (A) is pressed during measurement. (3) Pressing button (B) while the chronograph is stopped returns it to the reset display. Split time: The amount of time that has elapsed at some intermediate point from the starting line. Split time Split time Starting line Finish line <Split Time Measurement Procedure> The most recent split time is displayed for about 10 seconds whenever button (B) is pressed during chronograph measurement. (The SPL mark flashes while split time is displayed. ) * Pressing button (M) during chronograph measurement allows the mode to be changed. (3) Pressing button (B) continuously for at least 2 seconds causes the "city name" and "On or OF" to flash. [. . . ] · To clean a metal, plastic, or rubber watchband, wash away dirt with mild soap and water. Use a soft brush to remove dust and dirt jammed in the gaps in the metal band. NOTE: Avoid using solvents (thinner, benzine, etc. ), as they may mar the finish. 31 WARNING: Handling of the battery · Keep the battery out of the reach of small children. [. . . ]