Detailed instructions for use are in the User's Guide.
[. . . ] PRINTER PRESENTER UNIT
MODEL PPU-700
User's Manual
WEEE MARK
En
Ge
Fr
Sp
It
Du
Da
Por
Pol
Declaration of Conformity
This printer conforms to the following Standards:
Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC.
LVD : EN60950 EMC : EN55022 EN61000-3-2 EN61000-3-3 EN55024 Class A
This declaration is applied only for 230V model.
CITIZEN is registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón
IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. CAUTION: Use shielded cable for this equipment.
Sicherheitshinweis Die Steckdose zum Anschluß dieses Druckers muß nahe dem Gerät angebracht und leicht zugänglich sein.
For Uses in Canada This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus, as set out in the radio interference regulations of the Canadian department of communications. [. . . ] When using a large-diameter paper roll, be sure to provide a shock absorber to prevent shock during rotation of paper roll.
55
°
15. 5 120
5. 4 PHU-3*** (Paper Feed Unit) Installation
Refer to "Appendix-2. PHU-3*** (Paper Feed Unit) Installation".
-- 43 --
74. 5
Ra ng e
Pa pe rI ns tio er n Pa th
5. 5 Layout Examples of Control Box
Separation of Control Box from Printer allows you to enjoy free layout.
PPU-700 Layout Example (1/3)
Basic Type
Example 1) With board installed separately. PPU-700 Layout Example (2/3)
Example 2) With board installed below PPU-700.
Example 3) With board installed above PPU-700.
PPU-700 Layout Example (3/3)
Example 4) With paper holder installed under PPU-700.
Example 5) With paper holder installed above PPU-700.
-- 44 --
6. DIP SWITCHES
6. 1 Setting DIP Switches
The DIP switch is located on the serial interface board of the printer. (Be sure not to have the screw be lost. ) Slide the interface board to remove it. After setting, remount the interface board and screw it.
CAUTION!
G Pay attention to the edge of the interface board. Do not use longer size. ) G Turn the printer power off before setting DIP switches. G Do not use the printer with the interface board removed.
-- 45 --
6. 2 DIP Switch Functions
DIP Switches
Switch No. 1 2 3 4 5 6 7 8 INIT Reset Disabled Function ON OFF DIP switch setting is disabled. DTR/DSR 8-bit No parity Odd parity Factory Setting ON OFF OFF OFF OFF ON ON OFF
Setting and selecting DIP switch setting is condition for communication enabled. Communication mode Bit length Parity check Selecting parity Selecting baud rate Xon/Xoff 7-bit With parity Even parity
(See Table 1)
Table 1 Selecting baud rate
Baud Rate (bps) 2, 400 4, 800 9, 600 19, 200 Switch No. MEMORY SWITCHES
7. 1 Setting Memory Switches
Memory switch is a generic name for the following. (1) Memory switches MSW1, MSW2, MSW3, MSW4 (2) Customize value (3) Condition for communication through serial interface The memory switch can be selected, changed, or written by the combination of three actions: pressing the FEED switch, pressing and holding the FEED switch, and opening or closing the paper cover. Entering memory switch setting mode Set paper to the printer and keep the printer cover open. With the FEED switch pressed and held, turn the printer power on, and then press the FEED switch twice. Selecting memory switch When the FEED switch is pressed short (within 2 seconds), printing occurs in the order of "MSW1" "MSW2" "MSW3" "MSW4" "Write/ Factory Setting" "MSW1" . . . . . When the memory switch you want to change is reached, press and hold the FEED switch (for more than 2 seconds). Selecting each switch item There are eight setting items for each switch. Press and hold the FEED switch for long (within 2 seconds), the printer goes to the next item and prints the current setting of the item. Repeat pressing and holding till the item you want to change setting is reached. Changing the setting When the item you want to change is reached, press the FEED switch short. When you press the FEED switch long, the set value is accepted and then the printer goes to the next setting item.
-- 47 --
5.
Returning to the memory switch select mode When the setting of the desired content is completed, open the paper cover and then close the paper cover. [. . . ] 1 2 3 4 5 6 7 8 Funktion AN Werkseitige Einstellung DIP-Schalter-Einstellung AN ist aktiviert AUS DTR/DSR 8-Bit Keine Parität Ungerade Parität AUS AUS AUS AUS AN AN Reset Deaktiviert AUS
Einstellen und Wählen der DIP-Schalter-Einstellung Bedingungen für Kommunikation ist aktiviert Kommunikationsmodus Bitlänge Paritätsprüfung Auswählen der Parität Auswählen der Baudrate INIT Xon/Xoff 7-Bit Mit Parität Gerade Parität
(Siehe Tabelle 1)
Tabelle 1 Auswählen der Baudrate
Baudrate (Bit/s) 2, 400 4, 800 9, 600 19, 200 Switch-Nr. SPEICHERSCHALTER
7. 1 Einstellen der Speicher-Switches
Speicher-Switch ist ein generischer Name für folgendes. (1) Speicher-Switch MSW1, MSW2, MSW3, MSW4 (2) Anpassungswert (3) Bedingung für Kommunikation über serielle Schnittstelle Um Speicher-Switches auszuwählen, anzupassen oder zu schreiben, führen Sie folgende drei Schritte aus: Drücken Sie die Vorschubtaste (FEED) und halten Sie sie gedrückt, und öffnen oder schließen Sie die Papierabdeckung. Aktivieren des Einstellmodus für Speicher-Switches Führen Sie Papier in den Drucker ein und lassen Sie die Papierabdeckung geöffnet. [. . . ]