User manual CLASSE AUDIO SSP-30 MKII

[. . . ] SSP-30 MKII Preamplifier/Surround Sound Processor SSP-30 MKII Owner's Manual 2 IMPORTANT: SAFETY INFORMATION CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER'S MANUAL AND ALL THOSE MARKED ON THE UNIT. RETAIN THIS OWNER'S MANUAL FOR FUTURE REFERENCE. 1) Do not open the SSP-30 MKII for any reason, there are no user serviceable parts inside. An open unit, particularly if it is still connected to an AC source, presents a potentially lethal shock hazard. To prevent fire or shock hazard, do not expose the SSP-30 MKII to water or moisture. [. . . ] AV1 (-AV6) These six keys each directly access one of the AV Sources consisting of a Video Input and a hard-wired Analog Audio input plus any associated Digital Audio input selected during setup. The > and < Scroll keys must be used. ) 15 AUD1 (-AUD4) These four keys each directly access one of the Audio Sources consisting of a hard-wired Analog Audio input plus any associated Digital Audio input selected during setup. The > and < Scroll keys must be used. ) EX 7. 1 Press this key to listen to the Special 7. 1 Analog inputs. (The 7. 1 inputs cannot be accessed in the remote Zone. ) TAPE Press this key to Listen to tape through the Main output. This is also a useful key to use to Monitor the quality of a tape you are making. The Main Source continues to be the Source selected, so you can continue to Tape. Immediately press either the \/ or /\ keys to decrease or increase the volume or the < or > key to Scroll back and forth through the Ten Sources. MUTE THIS KEY HAS TWO FUNCTIONS: Press this key to Mute the Main outputs. ALSO: After pressing the ZONE key use this key to Mute the Zone outputs. The Main volume keys affect only the Main outputs. . 16 Section 5. 0 - Setting Up the SSP-30 MKII The SSP-30 MKII has a complete and well-thought-out configuration system, flexible enough for even a complex audio and Home Theater system. You will find setup to be quite intuitive, and that once set up, operation of the SSP-30 MKII will prove to be simple and straightforward. You may use either the On-Screen (TV) menu or the illuminated front panel readout. The same highlighted selection on the TV output is the visible on the panel. If the SSP-30 MKII is not on, and the green light is not lit, turn the unit "ON" with the rocker switch above the AC cord on the rear panel. (The SSP30 MKII may be left in "Standby" mode indefinitely when not in use. You may wish to unplug it or turn it completely off when you will be away for a long period of time, or when a thunderstorm threatens. ) You must use the Classé remote control to Set Up the SSP-30 MKII. The /\ and \/ keys (above and below the ENTER key) scroll through the main menus and the sub-menus, highlighting the choices. The box on the left shows the display on the TV screen and the box on the right shows the display on the front panel of the processor. Main Menu Audio setup Speaker setup Source setup Display setup Trigger setup Exit These displays show that you have accessed the Main menu and highlighted the Audio setup feature. You can scan through the available choices by pressing repeatedly the \/ and /\ buttons on the remote. When the feature you wish to adjust is highlighted press the ENTER key. Main menu Audio setup TV Display Panel display Pressing the MENU key to begin setup brings up screens similar to the ones above. Exit Configures 5 custom audio presets, increase or decrease Bass or Treble output, adjust LFE level, enable PL II panorama, adjust PL II width, adjust PL II dimension, adjust Reverb wetness. Defines and adjusts each Source, including Name, Digital input (if any), Preset and also adjusts Analog to Digital gain amount. [. . . ] , that you wish to record, to the same SOURCE the digital input is assigned to, and to which the analog audio is connected. Do not connect to REC. 6. 3. 4 6. 3. 5 6. 3. 5. 1 Follow the usual recording component instructions for recording. The digital output of the SSP-30 MKII's DIGITAL OUT always follows the input on the SOURCEs AV 1 through AUDIO 4. 26 6. 4 6. 4. 1 RECORDING DIGITAL AUDIO ONLY SSP D-VCR. Use a TOSlink cable to connect the output of the SSP-30 MKII's digital output to the digital input of the digital recording component. [. . . ]