User manual COMPRO V600 START UP GUIDE

[. . . ] COMPRO makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. COMPRO reserves the right to make revisions to this publication without obligation to notify any person or entity of any such changes. +886 2 2918 0169, Fax +886 2 2915 2389 4/F, No. 12, Alley 6, Lane 45, Pao Shin Road Hsintein City, Taipei, Taiwan. www. comprousa. com Table of Contents About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Switch TV/PC Mode Video Source Switch Sleep Mode Picture In Picture Switch audio between TV and PC Switch Resolution Channel Surfing Set Favorite CH List Favorite CH List Up Favorite CH List Down Display Menu Exit Menu Direction Up (CH +) Direction Down (CH -) Direction Left (Volume -) Direction Right (Volume +) Confirm Volume Control Channel Switch Stereo/SAP/Mono Number Keys Number Key Return to last channel 5 VideoMate V600 TV Box Using Guide Using at the first time Please refer to the above for correct setup to use V600 TV Box. After you have connected the power adaptor, you will see orange light shining out from the side. Press the power button at the top will turn on the TV Box and you will see orange light become blue light. If you have connect V600 TV box to your computer's video card, press the power button on the TV box or the power button on the remote control will switch between TV and PC signal. You may also press "TV/PC" button on the remote control to achieve the same result. Order of the Sources: TV Composite S-Video Component TV VideoMate V600 TV Box supports 9 resolutions from below. Resolution 1 -> 640*480 (4:3) Resolution 2 -> 800*600 (4:3) Resolution 3 -> 1024*768 (4:3) Resolution 4 -> 1280*720 (16:9) Resolution 5 -> 1280*1024 (5:4) Resolution 6 -> 1400*1050 (4:3) Resolution 7 -> 1440*900 (16:10) Resolution 8 -> 1600*1200 (4:3) Resolution 9 -> 1680*1050 (16:10) To change resolution, please open up menu and select the resolution you want. "RES" button from the remote controller can also switch the resolution. If using PIP feature, the refresh rates in Windows support resolutions below: Resolution 640 x 480 800 x 600 1024 x 768 1152 x 864 1280 x 1024 1280 x 720 1440 x 900 1400 x 1050 1600 x 1200 1680 x 1050 60 Hz Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Support Refresh Rate 70 Hz 72 Hz Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 75 Hz Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 6 OSD Menu Guide Menu button will open up OSD Menu, please use the direction key to navigate. Mode Presets (TV) (Monitor) (OSD) (Sound) Adjust the brightness (0~100) Default : 50 Adjust the Contrast (0~100) Default : 50 Adjust the Saturation (0~100) Default : 50 Adjust the Sharpness (0~15) Default : 0 Adjust the Hue ( 0~100) Default : 50 Choose between 2D/3D mode Default : 3D Mode 3 modes of picture settings (Standard/Game/Cinema) (Picture) Input Signal Channel Rename Fine tune Auto Scan Channel Swap CH Add/Erase Channel Video System (TV) (Monitor) (OSD) (Sound) Select Air or Cable for TV input signal type. Default by different countries (Picture) Resolution Refresh Rate Noise Reduction Display Type Input Source (TV) (Monitor) (OSD) (Sound) 640*480 800*600 1024*768 (default) 1280*720 1280*1024 1400*1050 1440*900 1600*1200 1680*1050 60Hz (default) 75Hz Adjust level of noise reduction. (0~8) Default is 4 LCD (default) CRT PDP TV Composite SV (S-Video) YCbCr (Component) PC 7 (Picture) (TV) (Monitor) (OSD) (Sound) OSD Position Press OK key, use direction keys to move OSD position OSDTransparency 1 2 3 4 Language Select your language Reset All Settings NO/YES (1 Cancel / 2 Reset All Settings) Information VideoMate V600 Version information Country/Region Select your country or region (Picture) Volume Treble Bass Loudness Reset (TV) (Monitor) (OSD) (Sound) Adjust volume (0-50) Adjust Treble volume (0-15) Adjust Bass volume (0-15) ON (enlarge the amplifier) / OFF (original signal) Reset sound settings (NO/YES) Channel Swap To swap the channel numbers, please select Channel Swap from the menu then select yes, and it will show as a sub menu. You may browse with the direction keys; Up and Down are going through the list while Left and Right are changing pages of the list. Select the channel number that you wish to swap and press OK, and then enter the number of the channel that you wish to switch. To reset to the original channel numbers, please rescan the channel table again by selecting Auto Scan in the menu. My Favorite Channel List My Favorite Channel List can store up to 10 channels that you watch the most and browse with "FAV UP" and "FAV DOWN" keys on the remote controller. To add channels to the favorite list, please turn to the channel you wish to add and press "SET FAV" on the remote controller. Press "OK" on the selected position. 8 PIP (Picture In Picture) You can start PIP function by clicking "PIP" button on the remote control. When PIP is working, press "PIP" button again will change the size of the TV screen; you may zoom twice and the third time you press "PIP", it will close the PIP function. And you can move the TV screen position with the blue arrow button on the remote. Channel Surfing Channel Surfing allows you to preview and find the channel you want by presenting in 9 squares. To access this function, please press "CH. SURF" button on the remote controller. [. . . ] It might also because the input source of V600 TV Box is not set to TV mode, please switch the video input source to TV. No Sound If the TV display without sound, please make sure you have connect your speaker to V600 TV Box's Line Out and make sure the speaker has turn on and volume is not at the minimum. If you switch to PC and PC does not have sound while TV has it, please make sure you have connected Line In from V600 TV Box to Line Out from your computer. TV picture is not clear? TV signal could be reduced by the branching. Try to move the computer to a TV set and connect the cable which is being used for the TV set. Once you connect the cable to our TV card, the static interfere the system. [. . . ]