User manual CURTIS TID855

[. . . ] All other servicing should be referred to qualified service personnel. This unit is equipped with a safety device which automatically turns the laser beam off when the disc compartment is opened. If a pin or other metal objects get inside the unit, this safety device may be deactivated. Do not place the unit in the following: Locations where the temperature is high . [. . . ] 18. SNOOZE KEY ALARM SET KEY SLEEP KEY EQUALIZATION PRESET KEY (EQ) REPEAT KEY FUNCTION KEY ( to select the CD, Radio function) STOP/RADIO BAND KEY POWER/ ALARM OFF KEY Battery compartment (for Remote control) Insert two(2) "AAA" /1. 5V(not included) batteries following the polarity as indicated in the compartment to the right. Remove the batteries in order to avoid the electrolyte leakage. Under Cabinet Mounting Instructions Tools Required Drill and 1/4" Drill Bit Ruler or Tape Measure Nail or Awl Scissors Screwdriver ­ Phillips Countersink (Optional) Masking Tape Safety Glasses 1 ­ Mounting template Parts Packed with your unit 1. Spacers (3pcs of 1/4" , 3pcs of 1/2", 3pcs of 1") Washers (3pcs) Phillips head screws (3pcs of 2 3/4", 3pcs of 1 5/8") Mounting Template Before Mounting Empty contest of the selected cabinet under which the unit will be mounted and thoroughly clean the underside of the cabinet to remove any grease residue which might be present. We recommend the unit be mounted at the front edge of the cabinet. Important: For secure mounting, the screws must go into the radio to a depth of at least 3/8". If the overall length from the bottom of the cabinet shelf to the bottom of the over hand is more the 1 3/4". A shim can be made from a sheet of plywood, using the Template to located the central lines for drilling the 1/4" mounting holes; the shim can be located between the cabinet shelf bottom and spacers. Make sure the wood is at least as thick as the excess over 1 3/4" if a shim is necessary, longer screws are required. Longer screws (Type#10-32) are available at most local hardware stores Cut out the template on the line indicated. The template size and the screw hold positions are identical to the top of the Clock radio. Mounting Procedure Step 1. If your cabinet does not have a overhang: a) Position template in desired location on underside of cabinet, flush with front edge. b) Then tape template in pace and go to step 2. If your cabinet have overhang: a) Measure the thickness of the overhang. In the event of a power outage, the time will not appear on the clock LCD Display, however the clock will continue to operate and the actual time will be maintained. The Clock LCD Display and other functions will resume once electrical power is restored if used the backup battery; Remove the battery if the clock is not used or stored for long periods of time CLOCK SETTING 1. 2. While in the CD or Radio mode, Press "Display/AL. Set" two time to enter the time mode. To deactivate the alarm (CD playing); Press either the STOP Button or Press the Power/AL. Press AL. SET KEY (on the remote controller) repeatedly to select tuner mode. Snooze Function If you want to snooze a few more minutes press the SNOOZE BUTTON (on the remote control) will deactivate the sound for 9 minutes. SLEEP FUNCTION Sleep time step change for PRESSING AND HOLDING SLEEP KEY (on remote control): 90->80->70->60->50->40->30->20->10->9->8->7->6->5->4->3->2->1->90 Sleep appears in display->sleep function activate To cancel sleep function, Press sleep key (on remote controller) one more time Sleep disappears in display-> cancel sleep function When the SLEEP time expires, the system will automatically turn OFF. TIMER FUNCTION (0:01 --------19:59) 1. Continue press the HOUR SET button (T/HOUR) adjust the hour of the time. Continue press the MINUTE SET button (T/MIN) adjust the minute of the time. When the count-down time reach to zero, the system will alarm for 3 minutes 4. Simply PRESS and HOLD the Hour set button (T/HOUR) and Minute set button (T/Minute) for 3-5 seconds the timer will be turn off. [. . . ] Press SKIP >>| button once to skip to the beginning of the next track. SEARCHING TRACKS Press and hold during play Backward------------SKIP |<< button Fast Forward------------SKIP >>| button PROGRAMMED PLAYBACK Up to 20 tracks can be programmed in to play in any desired sequence. In CD stop mode, Press MEMORY/C-ADJ button until "MEMORY" "Cd :01" is displayed in display. Press SKIP >>| button or SKIP |<< button to select a desired track to be memorized. [. . . ]