User manual CYBERHOME HGL 1710

[. . . ] 17" HDTV-READY LCD TELEVISION With Built-In DVD Player CH-HGL 1710 Operation Guide JPG TM HDTV R E A D Y SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). REFER TO QUALIFIED SERVICE PERSONNEL FOR SERVICING. Explanation of warning symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of not isolated dangerous voltage within the inside of the product that may be sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. Read the following instructions carefully WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR ANNOYING INTERFERENCE, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND ONLY USE THE RECOMMENDED ACCESSORIES. Read these instructions - When using this unit, basic precautions outlined in this section should always be followed. Keep these instructions - Retain this user manual for future reference. [. . . ] Use the 5/6 keys to navigate the menu and the ENTER key to confirm your selection. A dialog box will appear prompting you for the time to power on your TV. OSD - V POSITION Use this selection to adjust the Vertical position of the On-Screen Display. SET ON TIME 00 : 00 OSD TIMEOUT H POSITION V POSITION 5 SEC 3 4 Use the 5/6 keys to increase/descrease the values and the ENTER key to move between the hour and minute fields. After setting the ON TIME, select ON to enable and OFF to disable this feature. 1 2 Press the MENU key on the remote, use the6 key to select "OSD". Use the 3/4 keys to move the OSD menu to your desired vertical position. TIMER - OFF TIME Use this selection to set the time you would like the TV to power off. OFF TIME TIMER - SET TIME Use this selection to adjust the time related functions for the TV. Main Setup TIMER OFF ON SET SET TIME 02 : 28 : 18 1 2 Video Audio TV VGA OSD TIMER System SET TIME ON TIME OFF TIME SLEEP TIMER Press the MENU key on the remote, use the6 key to select "TIMER". Use the 5/6 keys to navigate the menu and the ENTER key to confirm your selection. A dialog box will appear prompting you for the time to power on your TV. SET OFF TIME 00 : 00 1 2 Press the MENU key on the remote, use the6 key to select "TIMER". Use the 3/4 keys to navigate the menu and the 5/6 keys to increase/decrease the time settings. Use the ENTER key to move from the hour, minute and seconds fields. 3 4 20 Use the 5/6 to increase/descrease the values and the ENTER key to move between the hour and minute fields. After setting the OFF TIME, select ON to enable and OFF to disable this feature. TELEVISION Television TIMER - SLEEP TIME Use this selection to set a period of time you would like the TV to power off. SLEEP TIMER TV - JUMP Use the JUMP key on the remote to return to the last channel tuned. 1 POWER EJECT OFF 15 Min 30 Min 60 Min 90 Min INPUT SELECT TV AV DVD SAP EQ ASPECT DISP JUMP 1 2 3 Press the MENU key on the remote, use the 6 key to select "TIMER". Use the 5/6 keys to navigate the menu and the ENTER key to confirm your selection. To disable this feature, select OFF. 1 2 3 Tune in a desired channel, antenna or cable. Tune in a different channel using the number or CH+/- key on the remote or CH 5/6 on the to panel. Press the JUMP key to return to the channel first tuned into. System This option is useful to reset your unit to its factory defaults and for general information about your unit. Main Setup TV - SAP This TV can receive SAP (Secondary Audio Programming) that accompanies the program, if the broadcaster transmits an additional sound signal as well as the original one. 1 POWER EJECT Video Audio TV VGA OSD TIMER System INPUT SELECT TV AV DVD SAP EQ 1 Press the MENU key on the remote, use the6 key to select "System". Press ENTER, general information is listed here. ASPECT DISP JUMP SYSTEM Information Model FW VERSION INPUT INFO HGL 1710A 1. 0. 025 NTSC 1 Press the SAP key on the remote control to enable/disable the SAP function. Load Default 2 3 Use the 6 keys to navigate to the next selection on the menu, "Load Default". Use the 3/4 keys to select YES or NO, then press ENTER. SYSTEM Information Load Default Yes No 21 TELEVISION Television TV - ASPECT This option allows you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. 1 POWER EJECT INPUT SELECT TV AV DVD SAP EQ ASPECT DISP JUMP 1 Wide screen mode is automatically displayed. 2 To change the format press the ASPECT key on the remote to change to a non-wide-screen screen format. 3 Press the ASPECT key on the remote to return to wide-screen format. 22 DVD PLAYER Playback Inserting a disc DVD SVCD VCD MP3 JPG CD Your unit has a built-in DVD player which uses a mechanical automatic SLOT-LOADING feature. All you need to do is simply insert your disc into the DVD unit's slot. The DVD unit will "grab" the disc when you have inserted it halfway. To eject, push the EJECT button next to the loading slot or on the remote control. While in front of the main unit, make sure the disc label is facing you. Hold the disc by the sides and with your fore finger through the hold in the middle and insert gently into the tray. Label Side Facing out 1 Look behind the TVhand screen on the right side to find the DVD player. 2 Hold the disc, careful not to touch the playing surface. [. . . ] This is to minimize any chance of damage from power surges or any potential hazard during your absence. 34 TROUBLESHOOTING UNIT DOES NOT POWER ON The AC power cord may be loose or not plugged in. Turn the power on with the remote control's POWER key, or turn the unit off, wait a few seconds, then turn the unit on with the front power switch. There must be a pause between powering the unit down and back on for a few seconds. THE DISC DOES NOT PLAY The disc may need cleaning. Ensure the disc is inserted with the label side facing the front of the unit. [. . . ]