User manual DANE-ELEC SO SPEAKY HDMI PLUS

[. . . ] faQs 4 4 5 7 10 13 18 22 23 24 2 Thank you for choosing the So Speaky hDmi + multimedia player. for better use of this product, please carefully read this user's manual. any imitation will be considered as counterfeit, and the person responsible will have to assume the legal consequences. The So Speaky hDmi + complies with the security standards pertaining to low voltage electronic devices, as described in the Standard Part 15 Class B fCC american certification, and the certificate of the European Union CE Standard EN55022 Class B, EN61000-6-3, EN61000-6-1. [. . . ] To change the language, please follow the instructions below: 1) Turn on the So Speaky hDmi + 2) access the main menu 3) Press the SETUP button on the remote control 4) go to "OSD language". 5) Select your language. 6) Press SETUP to finish and exit the menu. 10 5. 1 Connecting the device Connect the unit to an aC power supply using the power adaptor. When the blue led turns on, the device is ready to operate. 11 av Output mode To use the av output mode: select av as the output mode for the television. Press the viDEO key on the So Speaky hDmi + remote to select av (CvBS) OUT mode. The menu will appear on the television screen. YPbPr OUTPUT mODE (Progressive scan video component) To use the YPbPr output mode: select YPbPr as the output mode for the television. Press the viDEO key on the So Speaky hDmi + remote to select YPbPr OUT mode. You must also connect the av cable (white and red) for sound since the YPbPr cable only transmits the image. 12 hDmi Output mode To connect to a television and use the hDmi output: select hDmi mode, then press the viDEO key on the remote to switch to hDmi mode. You must also connect the av cable (white and red) for sound since the YPbPr cable only transmits the image. To connect to a hDmi monitor and use the hDmi output: press the viDEO key on the remote to switch to hDmi mode. iNSTrUCTiON fOr YOUr SOfTWarE SYSTEm Before basic operation, please set up hDD player as you like. Setup menu makes hDD player characteristic: adjust Tv format, language etc. The setup will be restored, even if power cut off unless you reset it. 6. 1 after the power and av cable has been connected, switch power on/off. The unit will start automatically data-reading with orange light on, and see the following start up menu. 6. 2. When reading finishes, screen displays a menu as in below picture: Press directional keys to select item and «enter» key to confirm. 13 2. Press «set up» button on the remote controller, setup menu appears on screen as below: press directional keys (up, down, left, right) to select item, then press «enter» key to confirm highlighted selection. in the event that video images are fuzzy or skip intermittently, please change the Tv mode setup. Tv display: «4:3 P/S», «4:3 L/B» or «16:9 LargE» are available. 6. video output: when your video output is connected to the Tv by av or Y. U. v. Press the "Display" key of the remote control to choose "Previous Chapter", "Next Chapter" and "Off". By pressing the "S-mode" button on the remote control, you can choose "Equalizer on", "Equalizer off" and "Off". The music mode can be set to Personal, Standard, Classical, Jazz, rock, Pop, Ballad and Dance. When playing DvDs, it is possible to switch between r & L audio channels or stereo sound. 18 7. [. . . ] finally, check that the power supply is switched on or is live, and that there isn't a power cut. Please reconnect to the power supply or switch the power key on the device's panel off and on again. Q4: When i switch the unit on, no image is displayed, there is no colour strip or it is fuzzy. The unit's video output mode doesn't match the display mode. [. . . ]