User manual DE DIETRICH DTE1111B

[. . . ] 23 FR 02 EN 24 ES 46 PT 68 Dear valued customer, DE 90 To discover a De Dietrich product is to experience the range of unique emotions which only high-value items can produce. The attraction is immediate, from the moment you set eyes on the product. The sheer quality of the design shines through thanks to the timeless style and outstanding finishes which make each appliance an elegant and refined little masterpiece in its own right, each in perfect harmony with the others. De Dietrich's design makes extensive use of robust and prestigious materials. [. . . ] 30 The safety wire (green/yellow) is connected to the ground terminal of the appliance and must remain connected to the ground terminal during installation. The fuse in your set-up must be 10 amperes If the power cable is damaged, it must be replaced by a cable or a special kit available from the manufacturer or its AfterSales Service Department. Tip In order to easily locate the reference information for your appliance, we recommend that you note it on the “AfterSales Service Department and Customer Relations” page. (This page also explains where to find this information on your appliance). 2 / INSTALLING YOUR APPLIANCE EN • GAS CONNECTIONS • Preliminary comments If your hob is installed above an oven or if proximity to other heating elements poses a threat of overheating the connection, you absolutely must insulate the cable in a rigid pipe. If a hose or soft pipe (in the case of butane gas) is used, it should not come into contact with a moving part of the cabinet, nor should it pass through a location that may become blocked. Warning All soft pipes and hoses whose service life is limited must must be at least two meters long and must be accessible along their entire length. They must be replaced before the end of their service life (marked on the pipe). Regardless of the means of connection chosen, ensure that the connection is leaktight, after installation, with soapy water. In France, you must use a hose or a pipe bearing the stamp NF Gaz The gas connection must be installed in compliance with applicable regulations in the country of installation. € Gas distributed by pipe; natural gas, propane-air gas or butane-air gas For your safety, you must choose from the three following connection options: — Connection with a rigid pipe made from copper and with screw-on mechanical connectors (G1/2 gas standard mark) Make the connection directly to the end of the elbow fitted on the appliance. € Connection with a wavy metal hose (stainless steel) with screw-on mechanical connectors (compliant with NF D 36-121 standard) whose service life is unlimited (Fig. € Connection with a reinforced rubber hose with screw-on mechanical connectors (compliant with the NF D 36-103 standard) whose service life is 10 years (Fig. When connecting your hob’s gas supply, if you have to change the direction of the elbow fitted on the appliance: ① Change the sealing washer. ‘ Screw on the elbow's nut, careful not to exceed a torque of 17 N. B Warning 31 EN 2 / INSTALLING YOUR APPLIANCE • Gas supplied by tank or cylinder (butane/propane) For your safety, you must choose from the three following connection options: — Connection with a rigid pipe made from copper and with screw-on mechanical connectors (G1/2 gas standard mark). Make the connection directly to the end of the elbow fitted on the appliance. € Connection with a wavy metal hose (stainless steel) with screw-on mechanical connectors (compliant with the NF D 36-125 standard) whose service life is unlimited (Fig. € Connection with a reinforced rubber hose with screw-on mechanical connectors (compliant with the NF D 36-112 standard) whose service life is 10 years (Fig. Tip You can obtain the adaptor and the sealing washer from your After-Sales Service Department. - Replace the gaskets and the knobs, paying careful attention to their direction and ensuring that the knobs are pushed in all the way. 05), using a small flat-head screwdriver, by turning two times counterclockwise. [. . . ] Be careful not to clog it during cleaning, as this will reduce the performance of your hob. Of the pan supports and gas burners If tough stains occur, use a non-abrasive . Commercially available coating, so you should avoid using any restorative product abrasive products. If the plate shows signs of rusting, remove the rust (with an emery cloth, for example) and restore the black coating with a commercially available high-temperature restorative product. [. . . ]