User manual DEWALT DC900KL

[. . . ] Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. D Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. [. . . ] - Appropriate measures have been provided for prevention of forced rupture and dangerous reverse current. DEWALT Li-Ion battery packs are exempted from national and international regulations applicable to dangerous goods. However, these regulations become relevant when transporting several battery packs together. Make sure that battery packs are packed according to the dangerous goods regulations as mentioned above to prevent short-circuiting. Labels on charger and battery pack In addition to the pictographs used in this manual, the labels on the charger and the battery pack show the following pictographs: Charge only between 4 °C and 40 °C Have defective cords replaced immediately Charger problem Battery problem Discard the battery pack with due care for the environment Do not incinerate the battery pack Charge only with dedicated DEWALT chargers The package contains: 1 Cordless midhandle driver/drill 1 Side handle 1 Battery pack (DC900K) 2 Battery packs (DC900KL) 1 Charger 1 Kitbox (K-models only) 1 Instruction manual 1 Exploded drawing Note: Battery packs and chargers are not included with N-models. Check for damage to the tool, parts or accessories which may have occurred during transport. Take the time to thoroughly read and understand this manual prior to operation. Read instruction manual before use Do not probe with conductive objects 1 2 3 4 5 6 7 8 9 10 Variable speed switch Forward/reverse slider Keyless chuck/auto spindle lock Torque adjustment collar Mode selector Three-gear selector Bit holder Grip Side handle Battery pack The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws. 10 Battery pack 11 Release button 12 Charger 13 Charging indicators (red) Auto-spindle lock The auto-spindle lock is engaged when the transmission is stationary. The chuck sleeve can easily be turned with one hand while the other supports the unit. Never connect the live (L) or neutral (N) wires to the earth pin marked E or . Use an approved extension cable suitable for the power input of your charger (see technical data). Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains. Always switch off the tool before inserting or removing the battery pack. Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorized DEWALT repair agent or a qualified electrician. Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet. Only fit 13 Amperes BS1363A approved plugs fitted with the correctly rated fuse (1). A) To fit the battery pack (10), line it up with the receptacle on the tool. Slide the battery pack into the receptacle and push until the battery snaps into place. [. . . ] To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete as purchased, to the point of purchase, for a full refund or exchange. If you need maintenance or service for your DEWALT tool, in the 12 months following purchase, it will be undertaken free of charge at an authorized DEWALT repair agent. If your DEWALT product becomes defective due to faulty materials or workmanship within 12 months from the date of purchase, we guarantee to replace all defective parts free of charge or, at our discretion, replace the unit free of charge provided that: The product has not been misused. [. . . ]