User manual DEWALT DCD920KX

[. . . ] Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Torque Chuck capacity Maximum drilling capacity Wood Metal Masonry Weight (without battery pack) LpA KPA LWA KWA (sound pressure) (sound pressure uncertainty) (acoustic power) (acoustic power uncertainty) VDC W min-1 min-1 min-1 min-1 min-1 min-1 Nm mm mm mm mm kg dB(A) dB(A) dB(A) dB(A) DCD925 18 NiMH/Li-Ion 450 0­500 0­1, 250 0­2, 000 0­8, 500 0­21, 250 0­34, 000 55 1. Vibration total values (triax vector sum) determined according to EN 60745: Vibration emission value ah Drilling into metal ahD = m/s² < 2. EN GLI S H The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. [. . . ] Do not incinerate the battery pack even if it is severely damaged or is completely worn out. Toxic fumes and materials are created when lithium ion battery packs are burned. If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. Without the protective cap in place, loose metal objects could short circuit the contacts, causing a fire hazard and damaging the battery pack. Take off the protective battery cap before placing the battery pack in the charger or tool (fig. Place the protective cap over the contacts immediately after removing the battery pack from the charger or tool (fig. WARNING: Make sure the protective battery cap is in place before storing or carrying a detached battery pack. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use. EN GLI S H NOTE: Li-Ion battery packs should be fully charged when stored. The package contains: 1 cordless percussion drill (DCD945/DCD935/DCD925 models) 1 cordless midhandle drill driver (DCD940/DCD930/DCD920 models) 1 Li-Ion battery pack (L1 models) 2 Li-Ion battery packs (L2 models) 2 NiMH battery packs (B2 models) 3 NiMH battery packs (B3 models) 1 Kitbox 1 Charger 1 Side handle 1 Instruction manual 1 Exploded drawing NOTE: Battery packs and chargers are not included with N-models. Check for damage to the tool, parts or accessories which may have occurred during transport. Take the time to thoroughly read and understand this manual prior to operation. In addition to the pictographs used in this manual, the labels on the charger and the battery pack show the following pictographs: Read instruction manual before use. Use only with DEWALT battery packs, others may burst, causing personal injury and damage. WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. Align the base of the tool with the notch inside the tool's handle (fig. Slide the battery pack firmly into the handle until you hear the lock snap into place. Press the release buttons (j) and firmly pull the battery pack out of the tool handle. Insert battery pack into the charger as described in the charger section of this manual. [. . . ] Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories. [. . . ]