User manual DEWALT DW625E

[. . . ] General 1 Keep work area clean Cluttered areas and benches can cause accidents. 2 Consider work area environment Do not expose Power Tools to humidity. Do not use Power Tools in the presence of inflammable liquids or gases. 3 Guard against electric shock Prevent body contact with earthed surfaces (e. g. [. . . ] · Never use cutters with a diameter exceeding the maximum diameter indicated in the technical data. 7 Threaded spindle 8 Stop 9 Knurled nut 10 Grip 11 Handwheel 12 Measuring lens 13 Scale 14 Plunge lock 15 Clamping screw 16 Depth stop 17 Fine adjuster for depth stop 18 Fine adjuster for parallel fence 19 Parallel fence 20 Revolver depth stop 21 Router base 22 Baseplate extension 23 Guiding knob Electrical safety The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate. Your DEWALT tool is double insulated in accordance with EN 50144; therefore no earth wire is required. Package contents The package contains: 1 Router 1 Parallel fence with fine adjustment and guide rods 1 Spanner # 22 1 Dust extraction adapter 1 Guide bush 1 Instruction manual 1 Exploded drawing · Check for damage to the tool, parts or accessories which may have occurred during transport. · Take the time to thoroughly read and understand this manual prior to operation. Mains plug replacement (U. K. & Ireland only) · Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorized DEWALT repair agent or a qualified electrician. · Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet. · Only fit 13 Amperes BS1363A approved plugs fitted with the correctly rated fuse (1). · The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. · Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws. Description (fig. A) Your DEWALT high performance Router has been designed for professional heavy duty routing of wood, wood products and plastics. 1 Lock-on button 2 Speed control dial 3 Collet nut 4 Spindle lock 5 Parallel fence locking bolt 6 Guide rods for parallel fence 17 en - 3 ENGLISH Assembly and adjustment Prior to assembly and adjustment always unplug the tool. · Using the 22 mm wrench, loosen the collet nut (3) a few turns and insert a cutter (24). C) Your DEWALT Router is supplied with a 1/2" collet fitted to the tool. · Separate the collet (25) from the collet nut (3) by pulling it firmly. A) The speed is infinitely variable from 8, 000 to 20, 000 min-1 using the electronic speed control dial (2) for uniform cutting results in all types of wood and plastics. · Turn the electronic speed control dial to the required level. 1 = 8, 000 min-1 2 = 12, 000 min-1 3 = 16, 000 min-1 4 = 18, 000 min-1 5 = 20, 000 min-1 Adjusting the depth of cut (fig. A) Your DEWALT Router is equipped with a high precision depth adjustment system including a revolver depth stop (20), a measuring lens (12) and fine adjuster (17). · Lower the router carriage until the cutter is in contact with the workpiece. · Tighten the plunge lock (14) by pushing it down. Never use a light socket. [. . . ] · Make sure the plunge limiter is always locked before switching ON. Loosen the plunge limiter and allow the router carriage to regain its rest position before switching OFF. · Subtract the diameter of the cutter from the outside diameter of the guide bush and divide by 2. This is the difference between template and workpiece. Maintenance Your DEWALT Power Tool has been designed to operate over a long period of time with a minimum of maintenance. [. . . ]