User manual DIRECTV SD-HBH

[. . . ] DIRECTV Receiver Owners Manual ® POWER MENU SELECT POWER MENU SELECT Models HAH-SA HBH-SA SD-HBH HUGHES WARRANTY REGISTRATION You may REGISTER ONLINE at: www. hns-usa. com/warranty or complete the registration form on the back of this manual. 1034354-0001 Rev. A Copyright 2001, 2002, 2003 Hughes Network Systems, Inc. , a wholly owned subsidiary of Hughes Electronics Corporation. This publication and its contents are proprietary to Hughes Network Systems, Inc. , a wholly owned subsidiary of Hughes Electronics Corporation. No part of this publication may be reproduced in any form or by any means without the written permission of Hughes Network Systems, Inc. , 11717 Exploration Lane, Germantown, Maryland 20876. [. . . ] When the OneLine guide appears, press the paddle or directional arrow buttons up or down to step to the next higher- or lower-numbered channel. Press the TURBO button to display the TurboTuneTM menu guide (HRMC-11 and HRMC-12 only). The INPUT button allows you to select programming from additional program sources such as a DVD player, VCRs, or a terrestrial TV antenna signal. Repeatedly press INPUT to cycle through each available input source in your system. Press the SAT component select button to control the DIRECTV® Receiver. You can program the AUX button to control another digital device such as an audio CD player. The DIRECTOR buttons provide convenient shortcuts to the Program Director, WatchWizardTM, audio, and video adjustment menus (HRMC-11 and HRMC-12 only). 1-LINE or 1-LINE TURBO or TURBO INPUT SAT DIRECTOR PROG SEARCH AUDIO VIDEO Using the remote control 13 Programming the remote control You can operate your TV, VCR, SAT, AUX device, or DVD (HRMC-11 and HRMC-12 only) devices using your remote control. Use the Code Entry or Code Scanning method to program the remote control. Using the Code entry method may be quicker, but you'll need to know the correct manufacturer's control codes for each component you want to operate. Code scanning may be more time-consuming, but you don't need to know manufacturer's control codes. Keep your remote control aimed at the device you want to control during this process. The remote control will send out the "power" command for the device being programmed. Choose one of the programming methods described below: Code Entry Use the REMOTE pane under the System Setup menu tab to program your HRMC-11, HRMC-12, or HRMC-13 remote control to operate your TV, VCR, SAT, AUX device, or DVD (HRMC-11 and HRMC-12 only). The AUX menu button can be used to control a CATV box or other type of device. Use the menu buttons to choose the desired type of device and display a brand name menu list from which you can select the manufacturer of your device. REMOTE Install Signal Info Features VCR Prefs Remote Test New Card Upgrade Watch TV Main Menu Wed, Oct 30 11:53AM Remote Control Settings Remote ID TV AUX VCR DVD Brand A Mark Akai Amstrad Anam AOC Audiovox Blaupunkt Highlight the device you want to select. If the button does not 001, 034, 038, 083, 199 Unit 1 Factory Defaults Device codes appear in the menu pane for the brand selected. Appendix B ­ Manufacturers device control codes, on page 41 also provides a complete list of device codes. 14 Using the remote control Code Scanning To use the Code Scanning method: 1. Repeatedly tap the top part of the CHANNEL (CH) button. CH P A G E 2. Continue to step through the codes until the component turns off, indicating you have found the correct component code. If you accidentally pass a code that responds or realize you may not have been aiming the remote control at the component, tap the lower part of the CHANNEL (CH) button to step backward through the codes. Press the remote control POWER button to verify the proper code by turning the device on and off. Press the device button (in this example, TV) again to lock in the code. Changing the Remote ID If you are using multiple satellite receivers in the same room, you may want to change the remote control ID to avoid interference or "cross talk. " The remote control ID can be a number from "001" to "008". [. . . ] HNS shall not be liable for damages in excess of the purchase price of the product less reasonable amount for use and wear, or for any incidental, special, punitive, or consequential damages of any nature whatsoever, or for any delays, loss of use, time, profits, revenue or savings, any commercial loss, inconvenience, damage to buyer's or to other person's property, arising from the use or inability to use the product, or otherwise for any failure to perform. HNS neither assumes nor authorizes any customer care center or any other person or entity to assume any other obligation or liability beyond that which is provided for in this limited warranty. No oral or written information or advice given by HNS, its dealers, distributors, agents or employees, shall create a warranty or in any way increase the scope of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations of implied warranties, so the above limitations or exclusions may not apply to Purchaser. [. . . ]