User manual DRAKE DIGITAL MPM860AG
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DRAKE DIGITAL MPM860AG. We hope that this DRAKE DIGITAL MPM860AG user guide will be useful to you.
Manual abstract: user guide DRAKE DIGITAL MPM860AG
Detailed instructions for use are in the User's Guide.
[. . . ] To obtain such warranty service, the original purchaser must: (1) Retain invoice or original proof of purchase to establish the start of the warranty period. DRAKE COMPANY or the nearest authorized service facility, as soon as possible after discovery of a possible defect, of: (a) the model and serial number, (b) the identity of the seller and the approximate date of purchase; and (c) A detailed description of the problem, including details on the electrical connection to associated equipment and the list of such equipment. DRAKE COMPANY or the nearest authorized service facility, or ship the same in its original container or equivalent, fully insured and shipping charges prepaid. [. . . ] Note that the output of the MPM860AG is related to the input signal's stability and level. A nominal input level of +10 dBmV ± 3 dB is desired at CH3 or CH4. The front panel gain control on the MPM860AG can then be adjusted to obtain a +45 dBmV output level. The MPM860AG is linear and if the input level is changed, the MPM output level will follow.
The R. L. Drake MPM860AG is a miniature analog double conversion heterodyne channel processor designed specifically to accept a channel 3 or channel 4 RF input from a typical consumer CH3/4 NTSC modulator. The input signal can be either double sideband as typical for such a modulator, or vestigial sideband modulated. The MPM860AG contains SAW filtering to insure that the output of the MPM860AG is a vestigial sideband output for use in a 6 MHz wide channel environment. Adjacent output channels are allowed.
® is a registered trademark of the R. L. Drake Company P/N: 3852548 Rev A-08-2010
CATV +100
GAIN
2
2
2
2
2
FRONT PANEL CONTROLS and INDICATORS
MPM860AG
MPM860AG
REAR PANEL CONNECTIONS / INTERNAL JUMPERS
R1
3
F1
POWER/ ERROR
CHANNEL 3/4 IN
F2
CATV +100
R2 R3
2 5
CH 4 CH 3 +5 V +12 V GND DC INPUT
CATV BCTV
R4
RF OUT
F3 F4
GAIN
MPM860AG Figure 1 F1 - POWER/ERROR Indicator Lights when the unit is connected to the required source of DC power via the rear panel DC INPUT connector. A flashing condition indicates an invalid channel setting or other conditions that would cause the unit to operate on an invalid channel. F2 - Channel Select Switch Sets the desired operating channel for standard CATV channels 02 through 135 or Broadcast TV channels 02 through 69. See also Item F3 which sets the type of channel (CATV or Broadcast TV) and sets the leading "1" for CATV channels 100 through 135. F3 - Mode Switch Sets the type of channel, CATV or Broadcast TV ("BC TV"). The first position of the switch ("+100") sets a leading "1" for CATV channels 100 through 135. Here are two examples: Setting for CATV channel "125"2 5
Figure 2 R1 - CH 3 / CH 4 INPUT +5 dBmV RF input. R2 - Ch 3 / CH4 SELECT Selects RF input between channel 3 and channel 4. [. . . ] FREQUENCY CHART The chart on the following page shows the standard CATV channel coverage. Where an offset is indicated, this amount of positive frequency offset is added to the frequency indicated in the middle column. As shown, this occurs only on channels required to be offset by the FCC. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DRAKE DIGITAL MPM860AG
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DRAKE DIGITAL MPM860AG will begin.