User manual DSC PC 4020 V3.0

[. . . ] Table of Contents Introduction Section 1: General System Operation 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 1. 8 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 2. 7 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 3. 7 3. 8 3. 9 4. 1 4. 2 4. 3 5. 1 5. 2 5. 3 5. 4 6. 1 6. 2 6. 3 6. 4 2 3 Getting to Know Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How to Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Alternate Arming Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If desired, your installer can program the system so that a valid access code will be required to prevent the system from auto arming. Swiping an access card on one of the partition's readers--if installed--will also prevent auto arming. 17 3. 4 Setting the Time and Date Keypad Command: [Master Code][9] To set the time and date on the system, perform the following: 1. Use the keypad arrow keys (< >) to scroll to the display "Set System Time. " Press [*]. Next, use the keypad arrow keys to scroll to the display "Set System Date. " Press [*]. Once the date and time have been programmed, press [#] to return the partition to its normal disarmed state. 3. 5 Activating Door Chime Keypad Command: [*][4] When the door chime feature is enabled, the keypad will emit five quick beeps when a zone is opened or closed. The keypad will only beep for zones which have the door chime zone attribute enabled. Often this feature is applied to entry doors so that you are notified when someone enters or exits the premises. To program the chime zone attribute for a particular zone, please ask your installer. NOTE: The door chime feature will not work on bypassed zones. 3. 6 View Event Buffer Keypad Command: [Master Code][9] Each system event is stored in an event buffer which can be viewed from any keypad. Use the keypad arrow keys (< >) to scroll to the display "View Event Buffer. " Press [*]. The event buffer can now be viewed, starting with the most recent event. When an event is presented, the first line of the display will show the event number and the partition on which the event occurred; the second line of the display will show the date and time of the event. Use the arrow keys to scroll through the list of all events in the event buffer. To stop viewing events, press [#]. 18 Section 3: System Administration 3. 7 [*][7] Command Outputs 1-8 Keypad Command: [*][7][1-8] These outputs must be programmed by your installer. These outputs will operate sets of lights, door strikes and various other items depending on what you and your installer have decided to add to your system. To activate the output, enter [*] [7] followed by the output number, from 1-8. For more information regarding the [*] [7] command outputs, please ask your installer. 3. 8 Keypad Control Keypad Command: [*][6][Master Code] The brightness of the keypad backlighting and the contrast of the keypad display can be adjusted. To alter the brightness and contrast from their default settings, perform the following: 1. Press [*] [6], then enter a valid access code which has the "System Master" or "Supervisor" option enabled. Use the arrow keys (< >) to scroll to the message "Keypad Setup. " Press [*]. Use the arrow keys to scroll through eight different settings of backlighting levels and press [*] to select the desired setting. Use the arrow keys to scroll to "Contrast Control. " Press [*]. Use the arrow keys to scroll through eight different settings of display contrast and press [*] to select the desired setting. [. . . ] Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches or arson. Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. s Motion Detectors Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. [. . . ]