User manual DSC PC4020

[. . . ] PC4020/PC4020CF v3. 5 · Installation Manual DLS2002 or higher WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. WARNING No t e to Ins ta ll ers Sy ste m F a ilu res Please Read Carefully This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. This system has been carefully designed to be as effective as possible. [. . . ] The crystal oscillator should be used for applications with a less reliable AC power source (Default=No). Clock Adjust Ref #: [00020308] This option is to compensate for any timebase inaccuracy. The panel will replace the last minute of each day with the number of seconds programmed in this section. For example, if the panel seems to lose nine seconds per day, program this section as [051]. NOTE: Do not schedule events to occur during the clock adjust time. 10. 2 Bell Circuit Supervision Ref#: [00020300] Bell Cut-off Ref#: [000200] System (Bell) Options The Bell Cut-off time will determine how long the fire/burg bell outputs will be active when an alarm occurs. The following system toggle options items will determine how the fire/burg bell outputs will operate. · Bell Shutdown: If enabled, the burg bell outputs will not Shutdown activate for a zone that has reached the swinger shutdown limit, if programmed. If disabled, a zone alarm will always activate the burg bell outputs (default=Yes). · Fire Timeout If enabled, the fire bell outputs will follow Timeout: the bell time-out. If disabled, the fire bell outputs will remain active until a valid access code is entered to silence the alarm (default=Yes). · Bell Delay Timer*: After an audible burglary alarm has Timer* occurred, the system will delay sounding the bells for the amount of time programmed in this timer. If 000 is programmed, there will be no delay before the bells sound (Default = 000). For more information regarding the bell output programming, please see Section 11. 1 `Main Panel Outputs`. For information on bell circuit wiring, please see 2. 12 `Bell Output Wiring (BELL+ and BELL-)`. 10. 4 Event Messages The following event messages can be modified from their default settings to suit the user's needs. To enter new labels, enter each character as outlined in Section 5. 4 'Zone Programming ­ Zone Labels'. These messages will only appear if the 'Special Messages' toggle option is enabled by the end user/system administrator, by entering [*][6][access code][0][2]. The zone tamper and zone fault messages will be displayed regardless of the [*][6] Special Messages option setting. 10. 3 Clock Options Set System Time and Date The System time and date can be programmed by the user and thus are not accessible in the Installer's Programming 31 FAIL TO ARM Ref #: [000100] This message will appear on every keypad on a partition when a valid code is entered but the partition is not ready to arm. ALARM WHEN ARMED Ref #: [000101] This message appears when a partition is disarmed after an alarm has occurred. The message will clear after five seconds and display the zone(s) that went into alarm. 4701 2-W SMOKE Ref #: [000102] This is the zone label for the 2-wire smoke zone on the PC4701 fire module. 4701 WATERFLOW Ref #: [000103] This is the zone label for the waterflow zone on the PC4701 fire module NOTE: If there is more than one of these fire messages to be displayed at once, the messages will scroll one after another. Once any fire alarm has been silenced a message 'Fire Bell Has Been Silenced' will be displayed on the partition and global keypads until the partition is armed. armed. [. . . ] The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. User should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. [. . . ]