User manual DYNATEK DC6-3

[. . . ] That the washing machine is levelled properly; something worth checking to aid the performance of your washing machine; 4. That the drum's fixing screws have been removed from the back of the washing machine. 2. 12) With just a bit of care, it will repay you with loyalty and devotion. With the necessary upkeep, it will wash for years and years to come. A correct distribution of your laundry is vital to the successful outcome of the wash and the life of the washing machine. [. . . ] Detergents that are specifically formulated for both hand and machine wash are an exception. One last secret: when washing with cold water, always reduce the amount of detergent you use: it dissolves less easily in cold water than in hot water, so part of it would be wasted. 4 3 In compartment 1: Detergent for pre-washing (powder) In compartment 2: Detergent for washing (powder or liquid) 1 2 In compartment 3: Additives (softeners, perfumes, etc. ) In compartment 4: Bleach and delicate bleach. Bleach cycle and stain removal button If bleaching is necessary, the extra case 4 (provided) must be inserted into compartment 1 of the detergent dispenser. When pouring in the bleach, be careful not to exceed the "max" level indicated on the central pivot (see illustration). The use of the additional bleach container excludes the possibility of using the pre-wash cycle. Traditional bleach can only be used on sturdy white fabrics, whereas delicate bleach can be used for coloured fabrics, synthetics and for wool. The detergent dispenser can be removed and cleaned: pull it outwards, as indicated in the figure. Then leave it under running water for a few minutes. Cutting costs efficiently A guide to environmentally friendly and economic use of your appliance. MAXIMISE THE LOAD SIZE Achieve the best use of energy, water, detergent and time by using the recommended maximum load size. SAVE detergent, time, water and between 5 to 15% energy consumption by NOT selecting Prewash for slight to normally soiled laundry. Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of a hot wash programme. SAVE energy and time by selecting the highest suitable spin speed to reduce the water content in laundry before using a drying programme. You cannot bleach with the “Silk” programme and with the “special programmes” (see page 4). Should you want to do it separately you must pour the bleach into the additional container 4, press button F (stain removal), star t the washing machine, then select one of the symbols according to the type of fabric. When you bleach during a normal wash cycle, pour the detergent and any additives in the special compar tments, press button F (stain removal), set the programme you desire and turn the washing machine on. 7 Instructions for installation and use Troubleshooting Before calling, read the following In most cases, when your washing machine fails to work, the problems arising can be easily solved without having to call for a technician. To check it, turn off the water supply, unplug the washing machine and follow the instructions on page 12, or call for technical assistance. Too much foam. Is the detergent appropriate for machine washing?Check whether the definition on its label reads “for machine wash” or “hand and machine wash”, or any other similar wording. An excessive amount of detergent, besides producing too much foam, does not guarantee a more effective wash, and causes scaling in the internal parts of the appliance. If, despite all checks, the washing machine fails to function and the problem persists, call your nearest authorised Customer Service Centre, providing the following information: - the nature of malfunction - the model type no. . . . . ) - the serial number (S/N . . . . ) This information can be found on the data plate situated at the back of the washing machine. The washing machine leaks. Is the metal ring of the inlet hose properly attached?Turn off the water supply, unplug the appliance and try tightening its attachment without forcing it. Turn off the water supply, unplug the appliance and try tightening its attachment. Excessive vibration during the spin cycle. Have all transit screws been removed durind installation?Adjust the feet and check them with a level. Always get assistance from authorised technicians and always insist on original spare parts. Technical characteristics Model Dimensions WAX 120 width 59, 5 cm height 85 cm depth 53, 5 cm from 1 to 6 kg voltage 230/240 Volt 50 Hz maximum absorbed power 2300 W maximum pressure 1 MPa (10 bar) minimum pressure 0, 05 MPa (0, 5 bar) drum capacity 52 litre up to 1200 rpm Capacity Electrical connections Water connections Spinning speed Control programs in programme 3; temperature 60°C; carried out with 6 kg load. compliance with IEC regulation 456 This appliance conforms with the following E. E. C. directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications 9 Instructions for installation and use Installation and removal When the new washer arrives Whether new or just transported to a new house, installation is extremely important for the correct functioning of your washing machine. After removing the appliance from its packaging, check that it is intact. The inside of the machine is supported, for transportation, by four screws on the back panel. [. . . ] Attention: Before attempting to examine this pre-chamber, first ensure that the machine has finished its programme and is empty. To gain access gently ease down the top of the plinth panel situated at the base of the machine, with a screwdriver etc, to release it. Place a shallow dish or tray below the cover of the pre-chamber to catch the small amount of water present. Re-fit the plinth cover by inserting the hooks on its lower edge into the slots and ease the top edge back into position. Fig. [. . . ]