User manual DYSON AIRBLADE AB03 TECHNICAL SPECIFICATION

[. . . ] ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo, ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of ZIH Corp. All other brand names, product names, or trademarks belong to their respective holders. For additional trademark information, please see "Trademarks" on the product CD. Proprietary Statement This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries ("Zebra Technologies"). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. [. . . ] Press SELECT to accept any changes and deselect the parameter. 13163L-002 A Z4Mplus/Z6Mplus User Guide 9/18/07 Configuration Control Panel Parameters 93 Table 11 · Printer Parameters (Page 12 of 22) Parameter Action/Explanation PARALLEL COMM. -BIDIRECTIONAL + Set Parallel Communications Select the communications port that matches the one being used by the host computer. Default: BIDIRECTIONAL Selections: BIDIRECTIONAL, UNIDIRECTIONAL To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. SERIAL COMM -RS232 + Set Serial Communications Select the communications port that matches the one being used by the host computer. This parameter will be eliminated in a future version of the firmware. Default: RS232 Selections: RS232, RS422/485, RS485 MULTIDROP To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. BAUD -9600 + Set Baud The baud setting of the printer must match the baud setting of the host computer for accurate communications to take place. Select the value that matches the one being used by the host computer. Default: 9600 Selections: 110, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200 To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. 9/18/07 Z4Mplus/Z6Mplus User Guide 13163L-002 A 94 Configuration Control Panel Parameters Table 11 · Printer Parameters (Page 13 of 22) Parameter Action/Explanation DATA BITS - 8 BITS Set Data Bits The data bits of the printer must match the data bits of the host computer for accurate communications to take place. Set the data bits to match the setting being used by the host computer. The "H" that is displayed indicates Hexadecimal and is not part of the value. Note · Do not use the same hex value for the control, format, and delimiter character. Default: 7E (tilde--displayed as a black square) Range: 00 to FF To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. 13163L-002 A Z4Mplus/Z6Mplus User Guide 9/18/07 Configuration Control Panel Parameters 97 Table 11 · Printer Parameters (Page 16 of 22) Parameter Action/Explanation FORMAT PREFIX <^>5EH + Set Format Prefix Character The format prefix is a two-digit hex value used as a parameter place marker in ZPL/ZPL II format instructions. The "H" that is displayed indicates Hexadecimal and is not part of the value. The printer looks for this hex character to indicate the start of a ZPL/ZPL II format instruction. Note · Do not use the same hex value for the control, format, and delimiter character. Press SELECT to accept any changes and deselect the parameter. DELIMITER CHAR <, >2CH + Set Delimiter Character The delimiter character is a two-digit hex value used as a parameter place marker in ZPL/ZPL II format instructions. Note · Do not use the same hex value for the control, format, and delimiter character. Press SELECT to accept any changes and deselect the parameter. 9/18/07 Z4Mplus/Z6Mplus User Guide 13163L-002 A 98 Configuration Control Panel Parameters Table 11 · Printer Parameters (Page 17 of 22) Parameter Action/Explanation ZPL MODE ZPL II + Select ZPL Mode The printer remains in the selected mode until it is changed by this parameter or by using a ZPL/ZPL II command. The printer accepts label formats written in either ZPL or ZPL II, eliminating the need to rewrite any ZPL formats that already exist. [. . . ] You irrevocably agree to submit to the exclusive jurisdiction and venue of the state or federal courts in the State of Illinois in the event of any litigation involving this Agreement or the Software. You agree that you shall not assert any claim that you are not subject to the jurisdiction of such courts, that the venue is improper, that the forum is inconvenient or any similar objection, claim or argument. Zebra may, in its sole discretion, choose to resolve any controversy or dispute between you and Zebra concerning this Agreement, or the existence, validity, breach or termination thereof, whether during or after the term by binding arbitration in accordance with the Commercial Arbitration Rules of the American Arbitration Association ("AAA"), as modified or supplemented under this Section 15, by providing notice to you. In the event that Zebra provides such notice, you hereby waive any right to institute a court or other dispute resolution proceeding with respect to such controversy or dispute and acknowledge arbitration in accordance with this Section 15 as the sole and exclusive means of resolving such controversy or dispute. [. . . ]