User manual EARLEX SPRAY STATION

[. . . ] Earlex recommend the use of appropriate ear protection when using this product. Sound pressure level: 85dB(A) G G G G G WARNING: The substances used with this spray gun (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials. ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING USED. Only use the unit as detailed in these instructions. 2 L0482 01-07. qxd 25/7/08 10:36 am Page 3 EXPLODED PARTS VIEW PARTS LIST Key Description 01. [. . . ] Place the motor unit onto a clean surface, free from any loose debris or liquids. ALWAYS KEEP THE MOTOR UNIT AS FAR AWAY FROM THE SPRAYING AREA AS POSSIBLE TO PREVENT PAINT CONTAMINATING THE MOTOR. No paint will be sprayed until the trigger on the spray gun is gently pulled. Before starting any work on spraying actual objects we suggest you spend some time practicing on cardboard or newspaper until you have got used to how the spray gun works G An airtight seal is essential for the correct operation of this gun. G Before operating the unit please ensure that the container is securely fixed to the gun body and the gland G Over time the gland seal (12) will wear and need adjusting. To check the gland nut is correctly fitted you nut (11) is not loose. will need a small adjustable spanner. Pull the trigger back and gradually tighten the gland nut by turning it in a clockwise direction until the needle is not free to move when the trigger is released. G To obtain the optimum setting gradually unscrew the nut by turning it in an anti-clockwise direction until the needle moves forward into the fluid tip (4). Re-adjust if necessary. SPRAY PATTERNS The spray gun has 3 different spray patterns ­ Horizontal, Vertical and Round (Fig. 2) The horizontal and vertical are recommended for large surfaces. The round spray is used for small objects or for areas - such as corners ­ that are difficult to reach. Fig. 2 To adjust the spray pattern, loosen the Air Cap Ring (1), adjust the position of the Air Cap (2) to obtain either a vertical, horizontal or round pattern then re-tighten the aircap ring. Round Jet Horizontal Jet Vertical Jet PAINT VOLUME The volume of paint sprayed is easily adjustable. (Fig. 3) Completely close Fluid Adjusting Screw (10) by turning this clockwise as far as it will go. Whilst pulling the trigger, begin turning the adjustment screw anticlockwise until the volume of paint you require is obtained. If the paint spray is too wide or contains too much paint turn the Fluid Adjusting Screw clockwise again. Once the correct spray pattern is obtained you are able to commence spraying. Fig. 3 SPRAYING TECHNIQUE 1. To obtain the best results always keep your spray gun level and at an equal distance from the object you are spraying, ideally 25-30cm (10"-12") (side to side or up or down) from the surface. Avoid spraying at an angle as this will lead to runs on the surface (Fig. 4a-4c). Let your arm control the left to right movement rather than your wrist as this will help to give you an even paint distribution over the whole area. Do not tip the spray gun to more than a 45o angle when the motor is switched off. You can tip the spray gun at more of an angle when spraying celings and decking etc, providing that the motor is switched ON. For spraying at angles, please change the direction of the Paint Feed tube (13) to the opposite angle that you are spraying, where there is more paint in the container. Fig. 4a Fig. 4b Fig. 4c 5 L0482 01-07. qxd 25/7/08 10:36 am Page 6 HELPFUL HINTS 1. [. . . ] Instead it is your responsibility to dispose of this type of waste by handing it over to special designated collection points for recovery and recycling. This product is marked with a `Wheelie bin' symbol with a cross on it to remind you of this action. The objective of this directive is to help conserve resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste please contact your local authority, take back facilities are free of charge. [. . . ]