User manual EARLEX SS200

[. . . ] Besteed ook speciale aandacht aan de veiligheidsvoorschriften en BEWAAR DEZE VOOR LATER. zal geen aansprakelijkheid voor het gebruik van dit product aanvaarden wanneer dit gebruikt wordt voor andere doeleinden dan welke staan beschreven in deze handleiding. Bitte lesen Sie diese Anleitung sorgfältig durch, bevor Sie das Gerät verwenden. Vielen Dank für den Kauf des Earlex Dampf-Tapetenablösers zur freihändigen Anwendung. Um das bestmögliche Ergebnis zu erzielen, lesen Sie bitte diese Anleitung, BEVOR Sie mit der Arbeit beginnen. [. . . ] WALL SET UP Store the Ceiling Waste Water Drainage Hose in the tube on the steam plate for security. Ensure the Waste Water Outlet Cover is pushed into the Waste Water Outlet to prevent steam escaping when using the unit on walls. Screw on the other end of the main hose to the boiler, and tighten by hand. Connect the rubber Boiler Vacuum Tube (F) from the the vacuum outlet of the main hose to the vacuum port on top of the unit. Place the end of the ceiling waste water hose into the waste water collection tank. E E DC 7. 3. F 8. 4. Use Velcro straps to secure both hoses together. 9. 10. NB: The ceiling waste water hose is only required when working on ceilings and is not needed for work on walls. It can be secured to the main hose using the Velcro straps and stored in the tube when not in use, or left off the assembly of the product. 3 PREPARATION If the plaster underneath the Paper or Artex is in a poor state of repair, care must be taken. If the plaster is old or cracked, the steam may penetrate, causing the plaster to "blister" or fall out. 3. 4. In order to achieve the fastest result it is best to gently score the wallpaper to be removed before operating the stripper. If you have heavily embossed paper or painted paper this is essential. Perforate the paper using a perforator tool, or alternatively score the paper in a criss-cross pattern approximately 6 inches apart with the edge of a wallscraper. A perforator tool is extremely useful for large surface areas and is available to buy through the online shop www. earlex. co. uk. For further availability please call our Customer Care Line on 01483 454666 quoting part number PPF1, or email enquiries@earlex. co. uk As with all decorating, care should be taken to protect carpets and furniture with covers. OPERATION DANGER FROM STEAM The unit has been designed for safe and fast removal of wallpaper but you must be aware at all times that steam is being produced and it can burn. FILLING WARNING: BEWARE OF HOT WATER DISCHARGE PRIOR TO STEAM EMISSION. · Overfill the unit by tilting the unit as hot water may be forced up the hose. Remove filler cap on top of the boiler and fill to the top with clean water, preferably hot. If refilling the unit, ensure that itis disconnected from the main power If filled to the maximum (point of overflow) 5 litres, the stripper will operate for approximately 78 minutes before requiring refilling. It will take longer to commence steaming on a maximum fill, taking up to 15 minutes. The capacity of 5 litres (9 pints) provides approximately 78 mins steaming time before the safety cut-out operates. Connect mains lead to the power socket and switch on the steam switch only, indicated by this symbol. It will take between 8 - 15 minutes (approx. ) for the unit to start producing steam depending on the temperature and the quantity of water used. WARNING - Hot water discharge before steam is produced. Once steam is produced at the steam plate, you will need to switch the vacuum pump on, indicated by this symbol. [. . . ] In the event of a fault occurring please contact our helpline on 01483 454666 before returning the unit to our Service Department at the address below together with a copy of your purchase receipt. All repairs will be dealt with speedily. EC Declaration of Conformity We declare that the unit SS200 conforms to: 2006/95/EC, EN60335-1, EN60335-2-54, 2004/108/EC, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 & EMF EN 50366. Tim Hopper - Technical Director MAINS CONNECTION This product is supplied with a specially prepared mains lead, if the cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified persons in order to avoid a hazard. If the moulded plug is cut off from the mains lead then the plug must be disposed of safely. [. . . ]