User manual EPSON DX 3800 START HERE

[. . . ] Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. Seiko Epson Corporation shall not be held liable for any damage resulting from electromagnetic interference that occurs from the use of any interface cables other than those designated as Epson Approved Products by Seiko Epson Corporation. EPSON® is a registered trademark, and EPSON STYLUSTM and Exceed Your Vision are trademarks of Seiko Epson Corporation. Microsoft® and Windows® are registered trademarks of Microsoft Corporation. [. . . ] Insert the flanged knob on the movable unit into the other end of the take-up reel core. 8 Choosing a Place for the Printer Instructions for placing the printer Choose a flat and stable location that can support the printer weight (about 150. 5 kg). Use only an outlet that meets the power requirements of this printer. Operate the printer under the following conditions: Temperature: 10 to 35ºC Humidity: 20 to 80% without condensation w Avoid locations that are subject to direct sunlight or near air conditioners. Do not cover the printer with a cloth, such as a blanket or tablecloth, when using the printer. Bodily injury may occur if it falls. Even the conditions above are met, you may not print properly if the environmental conditions are not proper for the paper. Keep the printer away from drying, direct sunlight, or heat sources to maintain the appropriate humidity. See the next section for detailed information on the space around the printer. Spaces around the printer Leave adequate room for easy operation, maintenance, and ventilation as shown below. (Values in the illustration below are the minimum. ) 9 English Warning: Avoid locations that are subject to excessive heat, poor ventilation, or dust; otherwise, it may cause smoke or fire. Settling the printer 1. Release the front casters. Setting up the Printer Removing the materials 1. Remove the all protective tapes from the printer and protective materials inside of the ink compartments. 2. Note: Unlike those used for material handling equipment such as carts, the casters attached to the printer stand are designed to move the printer a short distance on an indoor flat surface. To load cut sheet media with a length of Super A3/B (483 mm) or below, see "Loading cut sheet media with a length of Super A3/B (483 mm) or below" on page 18. If you are printing on thick paper (0. 5 to 1. 5 mm), see "Printing on thick paper (0. 5 to 1. 5 mm)" on page 19. 2. Press the Menu mode. button to enter Menu Note: When you use paper other than Epson special media, see the instructions included with the paper, or contact your supplier for more information. Loading cut sheet media longer than Super A3/B (483 mm) 3. Press the Paper Feed button to display TEST PRINT, and then press the Menu button. Make sure that the Paper Check light is on, and then set the paper lever to the released position. Press the Paper Feed button to display STATUS SHEET, and then press the Menu button. The paper lever may be locked if REMAINING PPR SETUP is set to ON: AT ROLL EXCHANGE. In this case, press and hold the Enter button for 3 seconds to print the barcode, so you can release the paper lever. 5. Press the Enter sheet. button to print a status After printing is finished, follow the message on the LCD panel to return to the READY state. 16 c 4. Load the sheet into the paper insertion slot until it comes out below. 7. appears on the LCD panel, press the Menu button to select the media, and then press the button to set the media. [. . . ] Note: Do not leave the paper in the printer for a long period of time; its quality will deteriorate. We recommend that you remove the paper from the printer after printing. 2. Connect the cable to the printer, and plug the other end of the USB cable to the computer or the other end of the Ethernet cable to the Ethernet hub. USB connection: Network connection: Note: When you connect both USB cable and Ethernet cable, install the printer software from each computer separately. [. . . ]