User manual EPSON EPL-5900L SETUP SHEET

[. . . ] Minimize the risk To minimize the risk of exposure to ozone, you should avoid the following conditions: Use of multiple laser printers in a confined area Operation in conditions of extremely low humidity Poor room ventilation Long, continuous printing together with any of the above Printer location The printer should be located so that the exhaust gases and heat generated are: Not blown directly into the user's face Vented directly out of the building whenever possible c Caution:adequate room around the printer to allow for sufficient ventilation. Leave Avoid locations that are subject to direct sunlight, excessive heat, moisture, or dust. Do not place the printer on a surface that is smaller than the printer's bottom panel. Doing so may cause troubles on printing and feeding due to the internal excessive load of the printer. [. . . ] Since radiation emitted by the laser is completely confined within protective housings and external covers, the laser beam cannot escape from the machine during any phase of user operation. LASER KLASSE 1 CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASERLAITE w Warning:sure that the printer is turned off. Be careful when working inside the printer as some components are sharp and may cause injury. 1. Important Safety Instructions Read all of the following instructions before operating your printer: Follow all warnings and instructions marked on the printer. Use a well-wrung cloth for cleaning and do not use liquid or aerosol cleaners. Avoid touching the components inside the printer unless instructed to do so in this guide. Although the printer is designed to be sturdy, rough handling can damage it. Avoid using outlets that other appliances are plugged into. w Warning:controls, or the performance of procedures and adjustments other than those The use of specified in this guide may result in hazardous radiation exposure. The maximum power of the laser diode is 5 mW and the wavelength is 770 to 810 nm. Average Radiation Power 27 µW at laser aperture of the print head unit Wavelength 770 to 810nm 2 Finding a Place for the Printer 2. Allow adequate space for easy operation and maintenance. This is a Class III b Laser Diode Assembly that has an invisible laser beam. The printer head unit is NOT A SERVICE ITEM, Therefore, the printer head unit should not be opened under any circumstances. An additional laser warning label is affixed to the inside of the printer. 15. 0 cm 10. 0 cm 60. 0 cm Laser Source 15. 0 cm 55. 0 cm Slots and openings in the cabinet and the back or bottom are provided for ventilation. Do not put the printer on a bed, sofa, rug, or other similar surface or in a built-in installation unless proper ventilation is provided. If you are not sure of the type of power available, consult your dealer or local power company. If you are unable to insert the plug into the outlet, contact a qualified electrician. If you use an extension cord, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. 10. 0 cm 70. 6 cm Place the printer where you can easily unplug the power cord. Keep the entire computer and printer system away from potential sources of interference, such as loudspeakers or the base units of cordless telephones. Continue to the back page. 3. 4 Connecting the Printer 5 Installing the Printer Driver Selecting your printer in the Chooser After you have installed the printer driver, you need to open Chooser to select your printer. This procedure is necessary the first time you use a printer and when you want to switch to another printer. Your Macintosh will always print using the last printer selected. Click the EPL-5900L icon Select USB Port Plugging in the Printer Make sure that the printer is turned off. Then plug the other end into a properly grounded electrical outlet. When you install the printer driver, the following software are installed. [. . . ] <Parallel> Note: If the EPSON Installation Program screen does not appear automatically, perform either of the following procedures. Double-click My Computer icon, right-click CD-ROM icon, and click Open in the menu that appears. Double-click My Computer icon, right-click CD-ROM and click Open in the menu that appears. Then double-click the folder of your language, and double-click the OS name you're using. [. . . ]