User manual EPSON STYLUS PHOTO R360

[. . . ] Also, make sure that you have the correct power cable for your power source. If the rated voltage and your outlet voltage do not match, contact your dealer for assistance. If the power cord is not attached to the printer, connect it to the AC inlet at the back of the printer. Plug the power cord into a properly grounded electrical outlet. c Installing Ink Cartridges This printer uses ink cartridges equipped with IC chips. [. . . ] Remove only the yellow tape from the ink cartridges. Caution: You must remove the yellow tape seals from the cartridges before installing them, or the cartridges will become unusable and you will be unable to print. If you have installed an ink cartridge without removing the yellow tape seal, you must remove that cartridge and install a new one. Prepare the new cartridge by removing the yellow tape seal before installing it in the printer. Do not remove the blue portion of the tape seal from the cartridges, or the cartridges may become unusable. Do not remove the tape seals from the bottom of the cartridges, or ink will leak out. If you install an ink cartridge without a chip, the printer may Do not touch this part. Align the tabs on each ink cartridge so that they rest on top of the tabs protruding from the base of the ink cartridge clamps. Make sure that the ink cartridge tabs are not under the tabs protruding from the base of the opened ink cartridge clamps. c Note: Install both ink cartridges. The printer moves the print head and begins charging the ink delivery system. This process takes about two and a half minutes. c Caution: Always press the e ink cartridge replacement button to move the print head. While the ink is charging, the Processing light flashes and the Select Photo display rotates. To connect the printer to a USB port, you will need a standard, shielded USB cable. Follow these steps: Note: For best results, you should connect the printer directly to the computer's USB port. If you must use multiple USB hubs, we recommend that you connect the printer to the first-tier hub. If your computer has more than one USB port, you may plug the cable in wherever is convenient. Plug the appropriate end of the cable into the USB port on the back of the printer. (The end that fits the printer has a different shape from the end that fits the computer. ) 3. Connect the other end of the cable to the computer's USB port. Installing the Printer Software After connecting the printer to your computer, you need to install the software included on the "Printer Software for EPSON Stylus Photo 915" CD-ROM shipped with your printer. Refer to the Photo Print Software Setup included in the online Reference Guide to install the Photo Print Software. The printer software CD-ROM contains: Printer software (printer driver and utilities) The printer driver runs, or "drives, " your printer; use it to make settings such as print quality, speed, media type, and paper size. Online guides The online Reference Guide helps you learn more about your printer. Detailed information about printing with your computer is included in this guide. System Requirements for online Reference Guide System CPU Microsoft Windows® Millennium Edition, 98, XP, 2000, or Mac OS 8. 5. 1, 8. 6, 9. x, Mac OS X 10. 1. 2 or later Pentium 150 MHz processor for Windows Me Pentium processor for Windows 98 Pentium 233 MHz processor for Windows XP Pentium 133 MHz processor for Windows 2000 Pentium 300 MHz processor or higher recommended Memory 16 MB RAM for Windows 98 32 MB RAM for Windows Me 16 MB RAM for Macintosh 32 MB or more recommended 64 MB RAM for Windows XP and 2000 128 MB RAM or more recommended Hard disk space CD-ROM drive Display Browser 5 MB to install the Reference Guide Double-speed (quad-speed or faster recommended) 640 × 480 pixel or 800 × 600 pixel resolution, with High Color (16 bit) or True Color (32 bit) setting Web browser (Microsoft Internet Explorer 4. 0 or later recommended) Refer to the appropriate section. Installing in Windows Follow the instructions in this section to install the printer. [. . . ] Note: The Problem Solver provides tips and instructions to help you solve most problems you may encounter when printing. The Problem Solver can be accessed through the EPSON folder, Status Monitor 3, or the printer software. For details, see the "Diagnosing the Problem" section of your online Reference Guide. Accessing EPSON Status Monitor 3 After installing the printer software, you need to access EPSON Status Monitor 3 to verify that the printer software has been installed correctly. For Windows Me, 98 and 2000 users, click Start, point to Settings, then click Printers. [. . . ]