User manual EPSON STYLUS PRO 9000

[. . . ] Adobe Acrobat version of the HTML On-line Reference Guide Contains the same information as the Online Reference Guide User's Guide Printer Parts Front view roll paper cover roll paper spindle control panel mounting brackets ink cartridge compartment lower cover paper basket paper set lever Rear view interface card slot cover AC in let ink cartridge compartment ink cartridge compartment parallel interface connector serial interface connector 2 ® All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein. [. . . ] This optional spindle is necessary if you wish to use the 3 inch diameter roll paper. Paper Handling 83 Note: If two roll paper spindles are attached to the printer, keep the unused roll wound up using the roll paper belt, to avoid paper jams. Make sure that the movable flange is fixed into the end of the roll paper properly. Paper Handling 84 3. Hold the roll paper spindle so that the fixed flange is positioned to the right side. 4. Place the right end of the spindle into the right mounting bracket inside the printer. Note: To mount the spindle correctly, match the color of the end of the spindle with the mounting bracket. Paper Handling 85 5. Place the left end of the spindle into the left mounting bracket inside the printer. 6. Close the roll paper cover or see "Loading the roll paper" following to load paper. Paper Handling 86 Loading the roll paper To load roll paper, follow the steps below. (In the illustrations below the paper basket is set to feed paper backwards. ) 1. Note: If two roll paper spindles are attached to the printer, keep the unused roll wound up using the roll paper belt to avoid paper jams. Press the Paper Source button repeatedly until the Roll Auto Cut light or Roll Cutter Off light is on. c Caution: If you are loading thick roll paper, select Roll Cutter Off. Paper that is too thick may damage the paper cutter. Paper Handling 87 4. Make sure the Operate light or Pause light is not flashing, then pull the paper set lever all the way up. The Paper Out light turns on and LOAD PAPERappears on the LCD panel. c Caution: Do not move the paper set lever up while the Operate light or Pause light is flashing. Load the paper into the paper insertion slot. Paper Handling 88 6. Pull the paper down through the paper insertion slot a small way. 7. Make sure that the bottom edge of the paper is straight and in line with the rows of punch holes. 8. Push the paper set lever all the way down, then close the roll paper cover. PRESS PAUSE BUTTON appears. Paper Handling 89 Note: If the Roll Auto Cut light is on, and the bottom edge of the roll paper was not cut properly after the previous print job, press the Cut/Eject button to recut the edge. 9. The print heads move and the paper feeds into the printing position automatically. Note: Even if you do not press the Pause button, the print heads move and paper feeds into the printing position automatically. Make the printer driver settings (see "Accessing the Printer Software" on page 33), then send a print job from the computer. Note: Make sure that the Paper Source setting in the printer driver matches the paper loaded in the printer. See "Cutting roll paper or printing page lines" on page 92. Paper Handling 90 Using the roll paper belt To keep the roll paper wound up, use the roll paper belt packed with your printer. [. . . ] Any computer can access the resources of a computer on the network. PhotoEnhance3 The EPSON software to change the shade of tone, to correct image data and to change the sharpness of the image data. port An interface channel through which data is transmitted between devices. printable area The area of a page on which the printer can print. It is smaller than the physical size of the page due to margins. Glossary 170 printer driver A software program that sends commands for using the features of a particular printer. See also driver. printing mode The number of dots per inch used to represent an image. Your printer has three printing mode settings: SuperFine (1440 dpi), Fine (720 dpi), and Normal (360 dpi). print queue If your printer is connected to a network, print jobs that are sent to the printer while it is busy are stored in a waiting line, or print queue, until they can be printed. Progress Meter A meter that shows the progress of the current print job for Windows. RAM Random Access Memory. [. . . ]