User manual FLAM MT 72-56 DIMENSIONS

[. . . ] Mount Laurel, New Jersey 08054-4620 · or by email to: pubs@okidata. com We welcome you to visit our multilingual web site: http://www. okidata. com FLAM, FLAMDATA, and FLAMPAGE are registered trademarks/ marques déposées/marcas registradas of Oki Electric Industry Company, Ltd. ENERGY STAR is a registered trademark of the United States Environmental Protection Agency. Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. 8 Quick Steps to Printing Customer Support Call 1-800-FLAMDATA. [. . . ] http://www. okidata. com e-mail: pubs@okidata. com Quick Setup 3 Getting to Know Your Printer Open Latch Paper Input Tray Paper Exit LED Array On/Off Switch Power/Status LED Image Drum Cartridge Manual Feed Slot IEEE 1284 Parallel Interface Port Power Cord Receptacle 4 Quick Setup 1 Unpack Your Printer s s Unpack your printer and place it on a flat, stable surface you've selected. Remove the printer from the plastic bag. If you are missing anything, contact your dealer. Note: As you unpack the accessories, please save the packing material in the event you need to repack the printer for shipping or moving. Check the contents FLAMPAGE 6w Printer Paper Feed Tray Toner Cartridge with LED lens cleaner Power Cord Software Support CD Light-shield bag Quick Start and Warranty booklets You will need to purchase: s s Paper (see page 13 for paper specifications) Interface cable: bi-directional IEEE-1284 parallel cable Quick Setup 5 2 Install the Paper Feed Tray s Insert the tabs on the bottom of the tray into the slots in the printer. s Swing the tray up and insert the tabs on the sides into the slots near the top of the printer. (You may need to install one side at a time). 6 Quick Setup 3 Remove the Protective Sheet s Lift the cover. s Lift out the Image Drum Cartridge. Quick Setup 7 Remove the Protective Sheet (continued) Guides s Pull out the protective sheet. s Replace the Image Drum Cartridge: a. Press down to lock. 8 Quick Setup 4 Install the Toner Cartridge s Lift out and discard toner well cover. s Unwrap toner cartridge. s Shake cartridge side to side to distribute toner. Quick Setup 9 Install the Toner Cartridge (continued) Tab s Remove tape from the toner cartridge. s Install the toner cartridge: a. Lower the right side into the well. 10 Quick Setup Install the Toner Cartridge (continued) s Push the lock lever forward until it stops. s Close the cover. Quick Setup 11 5 Connect to Your Computer We recommend that you use a Bi-directional parallel printer cable. Purchase a cable marked "IEEE 1284 compliant. " To comply with FCC regulations, the cable must be shielded and UL and CSA approved. s Note: FLAMDATA has tested and approved the following bidirectional cable: Part Number 70000803. See page 21 for purchasing information. s Make sure both your printer and computer are OFF. Insert the wide connector into the parallel port on your printer, then snap both wire clips into the notches on the cable connector. s s s Insert the other end into the parallel port on your computer and tighten the screws. Double click on Status Monitor. s The Status Monitor Dialog box appears. Click the Maintenance tab. 16 Quick Setup Print a Demo Page (continued) s Click the Demo button. s The Demo page prints. Click Help for more information about Status Monitor features. Quick Setup 17 Printing Transparencies, Labels and Special Media · Single Sheet Sizes: legal, letter, executive, A4, A5, B5, A6, user defined (min. 3" x 5" ) · Letterhead Stationery/ Preprinted Forms: Ink must withstand 392°F (200°C) for 0. 1 second. · Labels and Transparencies: ­ Transparencies, label carrier sheet and adhesive must withstand the fusing process heat of 392° F (200°C) for 1 second. ­ Use transparencies and label sheets designed for laser printers. s Adjust the guides. s s Insert media face-up, top of page in first. Select print. Quick Setup 18 Printing Envelopes Use this type s Adjust the guides. s s Insert the envelope flap down and to the left. Select print. ­ Use envelopes with a smooth, even surface that are designed for laser printers: no metal clasps, snaps, windows, or selfadhesive flaps ­ Maximum weight 24 lbs. ­ Monarch, Com-9, Com-10, DL, C5 19 Quick Setup Purchasing Supplies s s s s s Consult the dealer where you purchased your printer. [. . . ] ­ Monarch, Com-9, Com-10, DL, C5 19 Quick Setup Purchasing Supplies s s s s s Consult the dealer where you purchased your printer. Call 1-800-FLAMDATA (North America only) for the nearest Authorized Sales and Service location. Order toll-free by phone at 1-800-FLAMDATA (1-800-654-3282, North America only), using a major credit card. [. . . ]