User manual FLAM MT PLUS 68 DIMENSIONS

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date manuals and/or drivers are available from: http://www. okiprintingsolutions. com Trademark Information Oki and Microline are registered trademarks of Oki Electric Industry Company, Ltd. Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation. Apple, Macintosh and Mac are trademarks or registered trademarks of Apple Computer Inc. [. . . ] It is an alternative method of connecting printers instead of using the Microsoft TCP/IP port. SYSTEM REQUIREMENT Operating Systems with TCP/IP support and Oki printers that support TCP/IP. TO INSTALL THE FLAM LPR UTILITY NOTE: Some Operating Systems require administrator privileges in order to make changes. 1. Set up the printer driver by designating the output destination to Local Printer (LPT1:). For information on setting up your printer driver, see the printer user guide. Network configuration > 38 2. Insert the CD-ROM into the CD-ROM drive. Check Register in Startup if you want automatic startup as Windows boots up. Check Launch as minimized if you want to startup in the Icon state and click Next. You may be asked whether it is OK to change write permissions for the spool directory. If your printer is not discovered, click Cancel and you can type the IP address directly at IP Address:. 16. Refer to the On-line Help for information on how to use the utility. Network configuration > 39 UNINSTALLATION 1. Select Start>Programs>Okidata>OkiLPR Utility>Uninstall OkiLPR Utility. When the deletion has finished, the Uninstall Completescreen is displayed. Click OK. If a file that has been added after installation exists in the folder to install the OkiLPR utility or the folder to spool, you cannot delete the folder. Delete any unwanted files before running Uninstall OkiLPR Utility. Network configuration > 40 MICROSOFT WINDOWS OVERVIEW This chapter provides guidelines on how to print over the network from various Microsoft Windows platforms. The Ethernet address 8 of the printer can be found on the selfdiagnostic printout, which can be printed by pressing the push-button on the network card panel for three seconds and then releasing it. 8. Microsoft Windows > 45 Using TCP/IP protocol When using lpr in UNIX and other TCP/IP environments, please select Yes. To use in a TCP/IP environment, an IP address should be assigned to the Ethernet card. If Yes has been selected and TCP/IP is the only working protocol and the IP address has not already been assigned, you can either obtain an IP address automatically or assign an IP address. When Obtain an IP address automatically is selected, the device IP address will be automatically assigned by the DHCP server. In an environment without a DHCP server, please assign the IP address manually. If you are manually assigning an IP address, you need to enter: > An IP address > Subnet mask > Gateway address. Using Bonjour protocol Bonjour is the preferred protocol for printing data from the Macintosh environment. Using NetBEUI protocol Using NetBEUI makes it easy to manage your Oki product and print within the network environment of Windows. The new settings are transmitted to the network card but it still operates with pre-transmission settings. 12. Now that both Windows and the printer have been configured to use TCP/IP, the next step is to configure Windows to print to the network printer. Microsoft Windows > 46 NETBEUI PROTOCOL NETWORK PRINTER SETTINGS There are two configurable items under NetBEUI within the printer. These can be configured using the standard set-up utility described in "Device setup" on page 13. COMPUTER NAME Workgroup Comment 1. NAME ASSIGNED TO THE PRINTER PrintServer1 User definable description Although the workgroup name can be changed, it is recommended that it remains as PrintServer. Although there are some differences in configuration options between the various Windows platforms, the procedure for printing using NetBEUI is the same. [. . . ] Check that the network cable is correctly connected and that the green LED close to the printer's network interface is lit. If DHCP, BOOTP and RARP are not used, ensure they have been set to Disable. Troubleshooting> 77 CANNOT PRINT WITH LPR AND FTP Turn the printer off for 15 seconds and then on again. Use lp by default as euc and sjis are specific to PostScript printers. INCORRECT USER NAME ON THE BANNER PAGE If printing with lpr, the user name printed is unknown and the filename printed is the Spool file name. If printing with FTP, the user name printed is the user name entered during FTP login and the file name printed is the transmitted file name. [. . . ]