User manual FLAM PIKKU DIMENSIONS

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Oki Printing Solutions are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh, Mac, and Mac OS are registered trademarks of Apple Computers Inc. Hewlett-Packard, HP, and LaserJet are registered trademarks of Hewlett-Packard Company. [. . . ] Press the Up-arrow or Down-arrow buttons repeatedly until Configuration is highlighted. Press the Enter button to execute the command and a Configuration document is printed. After printing the configuration document, the printer returns to the ready to print status. System values and installed accessories are listed at the top of the first page while status values and settings follow. User's Guide> 43 INTERFACES AND CONNECTION Your printer is equipped with a selection of data interfaces: > Parallel ­ For direct connection to a PC. This port requires a bi-directional (IEEE 1284 compliant) parallel cable. > USB ­ This port requires a cable conforming to USB version 2. 0 or above. The printer may not work if a USB- compatible device is connected concurrently with other USB-compatible machines. When connecting multiple printers of the same type, they appear as *****, ***** (2), ***** (3), etc. These numbers depend on the order of connecting or turning on each printer. > Ethernet ­ For network cable connection. NOTE Interface cables are not supplied with your printer. User's Guide> 44 CONNECTING THE PARALLEL INTERFACE 1. Connect a parallel cable between the printer and computer. 3. Turn on the printer and then the computer. CONNECTING THE USB INTERFACE Do not connect the USB cable at this time. For the following accessories, you have to make the appropriate setting in your printer driver(s): > duplex unit > rewinder unit Refer to the Printing Guide for driver setting details. User's Guide> 59 TROUBLESHOOTING GENERAL If the printer display panel does not display anything or is still in stand-by mode 10 minutes after switching on, follow the printer shutdown sequence to switch it off. If the problem persists, contact your dealer. PAPER JAMS This section provides information to help you deal with problems that may arise when using the printer. The following paragraphs describe actions to take in the event of a paper jam and how to deal with unsatisfactory print results. Display panel messages about paper jams and relevant actions are given in this section while a list of other typical messages and suggested responses is given in "Appendix A ­ Display Panel Messages" on page 106. PAPER JAMS ­ PRINTER If a paper jam occurs, a message appears on the display panel in the printer Control Panel. You can press the Help button to display guidance on how to clear the jam. For full details of clearing jams, refer to the following paragraphs, which correspond to the paper jam messages. OPEN COVER, PAPER JAM, TTTTTT SIDE COVER Tray 1 can appear in place of the tttttt characters in the display panel message. In this example Tray 1 is used. User's Guide> 60 1. Squeeze the catch (1) on Tray 1 side cover and open the cover. 2. Holding it by the tab (2), turn the paper guide outward. 2 3. Carefully remove the jammed paper. User's Guide> 61 4. Put the paper guide back into position and close Tray 1 side cover. OPEN COVER, PAPER JAM, SIDE COVER 1. If the MP Tray is open, close it so that the side cover (1) is visible. 1 User's Guide> 62 2. Pull the release lever (2) and pull open the side cover. 2 3. Carefully remove the jammed paper. User's Guide> 63 4. Close the side cover. OPEN COVER, PAPER JAM, TOP COVER 1. Squeeze the top cover handle (1) and open the top cover. 1 WARNING! Be careful not to touch the fuser unit which is hot after printing. User's Guide> 64 2. Squeeze the basket handle (2) and raise the drum basket. 2 3. Carefully remove any paper on the belt. 4. If paper is jammed in the fuser unit, push the lock lever (3) in the direction shown to release the unit. WARNING! Be careful not to touch the fuser unit which may be hot after printing. If the fuser unit is hot, wait until it cools before attempting to remove any jammed paper. User's Guide> 65 Holding the fuser unit (4) by the handle, lift it out of the printer and place it on a flat surface. 4 3 5. Pull up the jam release levers (5) and remove the jammed paper. 5 User's Guide> 66 6. Carefully replace the fuser unit into the printer and turn the lock lever (6) in the direction shown to lock the fuser unit. 6 7. If paper is jammed near the paper exit, open the face-up stacker (7). 7 User's Guide> 67 8. Open the side cover (paper exit) (8) and remove the jammed paper. 8 9. [. . . ] For PS, printing is not carried out and the job is cancelled. Auto Continue ON OFF Manual Timeout OFF 30 sec 60 sec OFF 5 sec 10 sec 20 sec 30 sec 40 sec 50 sec 60 sec 90 sec 120 sec 150 sec 180 sec 210 sec 240 sec 270 sec 300 sec Wait Timeout User's Guide> 95 ITEM Low Toner VALUE Continue Stop DESCRIPTION Sets the printing operation when insufficient toner is detected. ON: continues printing the job, including any jammed pages, once the jam has been cleared. ON: prints an error report during the occurrence of an internal error. 0. 00 +0. 25 ­ +2. 00 -2. 00 ­ -0. 25 mm 0. 00 +0. 01 ­ +0. 08 -0. 08 ­ -0. 01 in Adjusts the position of the whole printing image (0. 25 mm, 0. 01 in interval) perpendicular to the direction of paper movement (i. e. [. . . ]