User manual FLAM PLATO MT 68-57 DIMENSIONS

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Oki Printing Solutions are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh, Mac, and Mac OS are registered trademarks of Apple Computers Inc. [. . . ] Enter User menu mode by pressing either the Enter button or the Up-arrow or Down-arrow button and press the latter two repeatedly until the desired menu is highlighted in the displayed list. Press the Up-arrow or Down-arrow buttons repeatedly until the desired Item is highlighted. Press the Up-arrow or Down-arrow buttons repeatedly until the desired Value is highlighted. (If you are setting a parameter, ensure that an asterisk (*) appears beside the selected parameter Value. ) Press the Online button to exit menu mode and return to the ready to print status. 3. 7. 8. Refer to the section entitled "Getting started" and "Appendix B ­ Menu system" for examples of using the menus. pro910 User's Guide> 40 GETTING STARTED This section provides information to help you get started with using your printer. PRINTER LOCATION Check that you have sufficient space for access: > around your printer: 20cm 8in 60cm 24in 60cm 24in 100cm 40in pro910 User's Guide> 41 > above your printer: 70cm 28in TURNING OFF/ON TURNING OFF No hard disk drive installed 1. If a hard disk drive is NOT installed, use the On/Off switch. pro910 User's Guide> 42 Hard disk drive installed 1. If your printer has a hard disk drive installed, hold down the Shutdown/Restart button (1) on the control panel for more than 2 seconds to start the shutdown process. 1 2. When the display panel shows that you can either turn off or restart the printer, use the On/Off switch to turn off the printer. pro910 User's Guide> 43 TURNING ON NOTE If the display panel shows that you can either turn off or restart the printer, press Shutdown/Restart to turn on the printer. 1. If the printer is turned off (no power), use the On/Off switch to turn on the printer. CHANGING THE DISPLAY LANGUAGE The default language used by your printer for display messages and for report printing is English. If required, this can be changed using the Panel Language Download Utility located on the installation CD under Optional Utilities. pro910 User's Guide> 44 CHECKING CURRENT SETTINGS Carry out the following steps to generate a Configuration report (Menu Map) to confirm that your printer is correctly configured. Ensure that there is Letter paper in Tray 1 (to be used in this operation). Ensure that the display panel indicates that the printer is ready to print. Press the Up-arrow or Down-arrow buttons repeatedly until Print Information is highlighted. All trademarks acknowledged. CLEANING THE LED HEADS You are advised to clean the LED heads: > any time you replace a toner cartridge (a LED lens cleaner is enclosed with each replacement toner cartridge) > if printing is showing signs of faded images, white stripes or blurred letters You can use a LED lens cleaner or dry, soft cloth for cleaning the LED heads. Open the top cover. pro910 User's Guide> 51 2. With an LED lens cleaner or soft cloth, gently wipe each of the four heads (1). Move the cleaner as shown, using a clean section of the cleaner with each pass. Be careful not to damage the guards (2). 1 2 3. Close the top cover. pro910 User's Guide> 52 CLEANING THE PAPER FEED ROLLERS Clean the paper feed rollers if paper jams frequently occur. Remove items like a wrist watch or bracelet and follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Open Tray 1 side cover and pull out the paper guide plate (1). 1 pro910 User's Guide> 53 3. Remove Tray 1 completely from the printer. 4. Gaining access through the gap left by Tray 1, wipe the 3 paper feed rollers (2) with a soft cloth lightly moistened with water. 2 5. Replace Tray 1. pro910 User's Guide> 54 6. Return the paper guide plate to its original position and close Tray 1 side cover. 7. Turn on the printer. pro910 User's Guide> 55 CLEANING THE PRINTER CASING 1. Follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Wipe the printer surface with a soft cloth moistened sparingly with water or neutral detergent. 3. Use a soft dry cloth to dry the printer surface. pro910 User's Guide> 56 4. Turn on the printer. EMPTYING THE PUNCH CHIP BOX (PUNCH UNIT OPTIONAL ACCESSORY) When the display panel indicates that the punch chip box is full, empty the box as follows: 1. Operate the Finisher lever and move the Finisher away from the printer. pro910 User's Guide> 57 2. Pull out the punch chip box, being careful to keep it level so as not to spill any chips. 3. Discard the chips in an appropriate place. 4. Replace the punch chip box carefully into the Finisher. pro910 User's Guide> 58 5. Check that the punch chip box has been replaced correctly then move the Finisher back into position, being careful not to trap your fingers. pro910 User's Guide> 59 OPTIONAL ACCESSORIES This section describes optional accessory equipment for your printer. The following accessories are available: > additional RAM memory > hard disk drive (required for verified and spooled printing, direct printing of PDFs, when collation errors appear, adding extra fonts) (pro910 only) > second, third paper tray (to increase paper input capacity) > high capacity feeder (equivalent to three paper trays) NOTE Tray configurations are: Tray 1 only, Tray 1 + 2nd Tray, Tray 1 + 2nd Tray + 3rd Tray, Tray 1 + HCF, Tray1 + 2nd Tray + HCF. > Finisher (for stapling printer output) > Punch unit (to extend Finisher functionality) pro910 User's Guide> 60 INSTALLING ACCESSORIES Each accessory (apart from the Finisher) comes complete with its own documentation which gives full instructions on installation. After installation, print out a Menu Map (Configuration document) to check that the installation has been successful. NOTE The Finisher and Punch unit must be installed by an authorized engineer. For the following accessories, you have to make the appropriate setting in your printer driver(s): > duplex unit > paper tray(s) > Finisher Refer to the Printing Guide for driver setting details. pro910 User's Guide> 61 TROUBLESHOOTING GENERAL If the printer display panel does not display anything or is still in stand-by mode 10 minutes after switching on, follow the printer shutdown sequence to switch it off. If the problem persists, contact your dealer. PAPER JAMS This section provides information to help you deal with problems that may arise when using the printer. [. . . ] Decrement setting when a white horizontal dotted line or a snowing image occurs in highcoverage print portions. Increment setting when a faded image occurs. Duplex Y Adjust 0. 00 +0. 25 ­ +2. 00 -2. 00 ­ -0. 25 mm 0. 00 +0. 01 ­ +0. 08 -0. 08 ­ -0. 01 in Paper Black Setting 0 +1 +2 -2 -1 pro910 User's Guide> 119 ITEM Paper Color Setting VALUE 0 +1 +2 -2 -1 DESCRIPTION Used for fine color adjustment for a significantly white horizontal dotted line, a significantly faded image or other such a problem that occurs in results printed on plain paper. Decrement setting when a white horizontal dotted line or a snowy image occurs in highcoverage print portions. Used for fine black adjustment for a significantly white horizontal dotted line, a significantly faded image or other such a problem that occurs in results printed on transparencies. [. . . ]